Intel S2600CW Technical Product Specification Download Page 97

Page: 97 / 210

Intel® Server Board S2600CW Family TPS

Intel® Server Board S2600CW Platform Management

Revision 2.4

commands. The power supply fans are treated as a system fan domain for which fan control

policies are mapped, just as for chassis system fans, with system thermal sensors (rather than

internal power supply thermal sensors) used as the input to a clamp algorithm for the power

supply fan control. This domain has both piecewise clipping curves and clamped sensors

mapped into the power supply fan domain. All the power supplies can be defined as a single

fan domain.

5.3.14.7.2

Use of Power Supply Thermal Sensors as Input to System (Chassis) Fan

Control

Some products require that the power supply internal thermal sensors be used as control

inputs to the system (chassis) fans, in the same manner as other system thermal sensors are

used for this purpose. The power supply thermal sensors are included as clamped sensors

into one or more system fan domains, which may include the power supply fan domain.

5.3.14.8

Fan Boosting due to Fan Failures

Intel® Server Systems supporting the Intel® Xeon® processor E5-2600 v3 and v4 product

families introduce additional capabilities for handling fan failure or removal as described in

this section.

Each fan failure shall be able to define a unique response from all other fan domains. An OEM

SDR table defines the response of each fan domain based on a failure of any fan, including

both system and power supply fans (for PMBus*-compliant power supplies only). This means

that if a system has six fans, there will be six different fan fail reactions.

5.3.14.9

Programmable Fan PWM Offset

The system provides a BIOS Setup option to boost the system fan speed by a programmable

positive offset or a “Max” setting. Setting the programmable offset causes the BMC to add the

offset to the fan speeds that it would otherwise be driving the fans to. The Max setting causes

the BMC to replace the domain minimum speed with alternate domain minimums that also are

programmable through SDRs.

This capability is offered to provide system administrators the option to manually configure

fans speeds in instances where the fan speed optimized for a given platform may not be

sufficient when a high end add-in is configured into the system. This enables easier usage of

the fan speed control to support Intel as well as third-party chassis and better support of

ambient temperatures higher than 35°C.

5.3.15

Power Management Bus (PMBus*)

The Power Management Bus (PMBus*) is an open standard protocol that is built upon the

SMBus* 2.0 transport. It defines a means of communicating with power conversion and other

devices using SMBus*-based commands. A system must have PMBus*-compliant power

supplies installed in order for the BMC or ME to monitor them for status and/or power

metering purposes.

Summary of Contents for S2600CW



















































































































































































































Search results

Summary of Contents for S2600CW

Reviews:

Related manuals for S2600CW

Brands by name

Popular brands

Intel S2600CW, Technical Product Specification

Search results

Summary of Contents for S2600CW

Reviews:

Related manuals for S2600CW

Brands by name

Popular brands