Intel M50CYP2UR Series System Integration And Service Manual Download Page 119

Page: 119 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

119

6.9.2

12 x

3.5” Backplane Installation

Required Tools and Supplies

•

Anti-static wrist strap and conductive workbench pad (recommended)

•

Phillips* head screwdriver #1

Figure 158. 12 x 3

.5” Backplane Removal

Power off the system and remove the power cable(s).

Remove the system top cover (see

Section 6.1.1

Remove the air duct (see

Section 6.2.1

Remove all drives and drive blanks from the front drive bays).

Disconnect all cables from the backplane.

Remove all fastener screws securing the backplane to drive bay (see Letter A).

Slide the backplane up from the bottom of the chassis and remove the backplane from the server chassis
(see Letter B).

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands