Intel IXP45X Developer'S Manual Download Page 690

Page: 690 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—Expansion Bus

Controller

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

690

Order Number: 306262-004US

12.4.5

Expansion Bus Inbound Timing Diagrams

The next several timing diagrams show several representations of some of the

supported inbound bus protocol. The Expansion bus controller is not limited to the

possibilities of the timing diagrams shown. Timing diagrams with varying combinations

of NOPS, Master waits, back-to-back transfers are all supported as long as the rules

that are described in

Section 12.4.2, “Inbound Transfers” on page 681

are followed.

12.4.5.1

Back-to-Back 1-Word Inbound Write with EX_SLAVE_CS_N

Deasserted

Figure 150

shows three 1-word writes. The first transaction is a 1-word write with no

waits. In the second write the master chose to insert a NOP in cycle 3. In the third

write, the Expansion bus controller is busy and asserts EX_WAIT_N in cycle 9. The

Expansion bus controller will assert EX_WAIT_N one cycle after the assertion of

EX_SLAVE_CS_N and EX_WR_N if its not ready to transfer data. If EX_WAIT_N is

asserted, the master cannot end the burst until EX_WAIT_N is deasserted. For 1-word

writes, the Expansion bus controller only transfers the data that is presented on the

cycle that EX_SLAVE_CS_N is deasserted. In the timing diagram the master chose to

tri-state EX_DATA/EX_PARITY in cycles 3 and 7, however this is not mandatory and can

be driven.

12.4.5.2

Back-to-Back 1-Word Writes without Deasserting

EX_SLAVE_CS_N

Figure 151

shows multiple 1-word writes without deasserting EX_SLAVE_CS_N. The

external master must deassert EX_WR_N between the writes and the Expansion bus

controller will assert EX_WAIT_N once EX_WR_N is re-asserted in cycle 4. When the

Expansion bus controller observes EX_WR_N deasserting in cycle 2 and 6, it captures

the data.

Figure 150. Back-to-Back 1-Word Inbound Write with EX_SLAVE_CS_N Deasserted

B4438-01

EX_ CLK

- 0 -

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

- 9 -

EX_ IXPCS_N

EX_ ADDR

EX_RD_N

EX_WR_N

EX_BE_N

EX_ BURST

EX_ WAIT_N

EX_ DATA

EX_ PARITY

STATE

- 10 -

- 11 -

- 12 -

- 13 -

- 14 -

ADDR0

DATA0

DATA2

IDLE

DATA0

PAR0

BE0

ADDR1

IDLE

NOP

DATA1

PAR1

BEy

DATA0

IDLE

DATA1

IDLE

ADDR2

BE2

WAIT

DATA2

PAR2

NOP

DATA1

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands

Intel IXP45X, Developer'S Manual

Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands