background image

User’s Manual 

 

EMX-965GME

 
 

9

Specifications Summary

 

I/O 

Internal I/O 

3 x USB connectors support additional 6 USB ports 

1 x 20-pin ATX Power connector,1 x IDE 40-pin connector for two devices 

2 x COM port header,3 x SATA connectors,1 x Front panel audio connector 

1 x Audio amplifier connector,1 x System panel connector 

1 x LVDS connector,1 x Inverter Power connector,1 x CPU Fan connector 

1 x System Fan connector,1 x Digital IO header 

1 x SPDIF Out connector reserved 

Back Panel 

1 x PS/2 Keyboard,1 x PS/2 Mouse,2 x RS-232,1 x VGA port,1 x DVI port 

4 x USB 2.0/1.1,1 x LAN RJ45 Port (one existed, another option) 

5.1 + 2 CH Audio I/O (3 jacks) 

Display 

Chipset 

Intel Graphics Media Accelerator X3100 

Display Memory 

Intel DVMT 4.0 supports 384 MB video memory 

Resolution 

2048 x 1536 @ 32 bpp(@ 60Hz) 

Dual Display 

CRT + LVDS, or CRT + DVI-D 

LVDS 

Dual-channel 24-bit LVDS 

DVI 

Chrontel CH7307C DVI transmitter up to 165M pixels/second 

Audio 

Audio Codec 

Realtek ALC888 Audio Code 

5.1+2 ch. with two independent audio stream 

Audio Interface 

Mic in, Line in, Line out 

Audio Amplifier 

TPA3005D2 Stereo 5Watt per channel 

Ethernet 

LAN1 

Realtek RTL8111B PCI-E Gigabit Ethernet Controller 

LAN2 

Realtek RTL8111B PCI-E Gigabit Ethernet Controller (optional) 

Mechanical & Environmental 

Power Type 

ATX 

Operating Temperature 

0~60°C (32~140°F) 

Operating Humidity 

0%~90% relative humidity, non-condensing 

Size (L x W) 

6.69" x 6.69" (170 mm x 170 mm) 

Weight 

0.88 lbs (0.4 Kg) 

 

* Specifications are subject to change without notice.

 

Summary of Contents for EMX-965GME












































Reviews: