Intel DG41AN Product Manual Download Page 16

Intel Desktop Board DG41AN Product Guide 

16 

Audio Subsystem  

The onboard audio subsystem consists of the following: 

 

Intel

®

 ICH7  

 

Realtek ALC888VC audio codec 

 

Back panel audio connectors (see Figure 19) 

 

Front panel audio header supporting both Intel High Definition Audio and AC ’97 
Audio (see Figure 18, A) 

The audio subsystem supports the following features: 

 

A signal-to-noise (S/N) ratio of 95 dB  

 

Independent 5.1 audio playback from the back panel connectors and stereo 
playback from the Intel High Definition Audio front panel header  

Table 4 lists the supported functions for the front panel and back panel audio jacks.   

Table 4.  Audio Jack Retasking Support 

 Mic 

Line out/ 
Headphone 
or Speaker  

Line in 

Rear 
Surround 

Center/ 
Subwoofer 

Front Panel Header 

Green No Yes 

No  No 

No 

Pink  

Yes 

No 

No 

No 

No 

Back Panel Connectors 

Blue No 

Yes 

Yes Yes 

No 

Green No Yes 

No  No 

No 

Pink  

Yes 

No 

No 

No 

Yes 

 

Legacy Input/Output (I/O) Controller 

The Winbond 83627DHG-P legacy I/O controller provides the following functions: 

 

One serial port interface via an onboard header 

 

One parallel port  

 

Serial IRQ interface compatible with serialized IRQ support for PCI systems 

 

Intelligent power management, including a programmable wake up event interface 

 

PCI power management support 

Summary of Contents for DG41AN






































































Reviews: