Intel CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN Page 10 Design Manual Download | Manualshive

Page: 10 / 126

background image

Introduction

10

Thermal and Mechanical Design Guidelines

1.1.3

Document Scope

This design guide supports the following processors:

•

Intel

®

Core™2 Duo processor E8000 series with 6 MB cache applies to Intel

®

Core™2 Duo processors E8600, E8500, E8400, E8300, E8200, and E8190

•

Intel

®

Core™2 Duo processor E7000 series with 3 MB cache applies to Intel

®

Core™2 Duo processors E7600, E7500, E7400, E7300, and E7200

•

Intel

®

Pentium

®

dual-core processor E5000 series with 2 MB cache applies to

Intel

®

Pentium

®

dual-core processors E5700, E5500, E5400, E5300, and E5200

•

Intel

®

Pentium

®

dual-core processor E6000 series with 2 MB cache applies to

Intel

®

Pentium

®

dual-core processor E6800, E6700, E6600, E6500, and E6300

•

Intel

®

Celeron

®

processor E3000 series with 1 MB cache applies to the Intel

®

Celeron

®

processor E3500, E3400, E3300, and E3200

In this document when a reference is made to “the processor” it is intended that this
includes all the processors supported by this document. If needed for clarity, the
specific processor will be listed.

In this document, when a reference is made to the “the reference design” it is
intended that this means ATX reference designs (E18764-001) supported by this
document. If needed for clarify, the specific reference design will be listed.

In this document, when a reference is made to “the datasheet”, the reader should
refer to the

Intel

®

Core™2 Duo Processor E8000 and E7000 Series

Datasheet,

Intel

®

Pentium

®

Dual-Core Processor E6000 and E5000 Series

Datasheet, and

Intel

®

Celeron

®

Processor E3000 Series

Datasheet. If needed for clarity the specific

processor datasheet will be referenced.

Chapter 2 of this document discusses package thermal mechanical requirements to
design a thermal solution for the processor in the context of personal computer
applications.
Chapter 3 discusses the thermal solution considerations and metrology
recommendations to validate a processor thermal solution.
Chapter 4 addresses the benefits of the processor’s integrated thermal management
logic for thermal design.
Chapter 5 gives information on the Intel reference thermal solution for the processor
in BTX platform.
Chapter 6 gives information on the Intel reference thermal solution for the processor
in ATX platform.
Chapter 7 discusses the implementation of acoustic fan speed control.

The physical dimensions and thermal specifications of the processor that are used in
this document are for illustration only. Refer to the

datasheet

for the product

dimensions, thermal power dissipation and maximum case temperature. In case of
conflict, the data in the datasheet supersedes any data in this document.

«
...
8
9
10
11
12
...
»

Summary of Contents for CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN































































































































Reviews:

No comments

Related manuals for CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

APS6-400 Series

Brand: Eaton Pages: 114

ST62GP-EMU2 HDS2 Series

Brand: STMicroelectronics Pages: 58

Digital Encoder Plus

Brand: IDT Pages: 98

Brand: Lutron Electronics Pages: 4

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Brand: MICROENER Pages: 24

Brand: Atmel Pages: 2

Brand: Supermicro Pages: 131

Brand: National Instruments Pages: 121

Brand: WTI Pages: 178

Brand: Mitsubishi Pages: 188

Brand: ICP DAS USA Pages: 62

Brand: SilverStone Pages: 17

Brand: AXIOMTEK Pages: 2

Brand: MA Pages: 4

Brand: NAUTICAST Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands