Intel BLKDG33TLM - G33 Express Socket775 mATX Motherboardw/Video Product Manual Download Page 9

Page: 9 / 90

1 Desktop Board Features

This chapter briefly describes the features of Intel

Desktop Board DG33TL. Table 1

summarizes the major features of the Desktop Board.

Table 1. Feature Summary

Form Factor

microATX (243.84 millimeters [9.60 inches] x 243.84 millimeters
[9.60 inches])

Processor

Support for an Intel

processor in the LGA775 package

Main Memory

•

Four 240-pin, DDR2 1.8 V (only) SDRAM Dual Inline Memory Module

(DIMM) sockets

•

800/667 MHz single or dual channel DDR2 SDRAM interface

•

Support for up to 8 GB of system memory

Chipset

Intel

G33 Express Chipset consisting of:

•

Intel G33 Express Chipset Graphics and Memory Controller Hub

(GMCH)

•

Intel

82801IR I/O Controller Hub (ICH9R)

Graphics

•

Intel G33 Express Chipset Graphics and Memory Controller Hub
(GMCH)

•

One PCI Express* x16 connector supporting PCI Express graphics

cards

Audio

•

8-channel (7.1) onboard subsystem, featuring:

―

Intel

High Definition Audio interface

―

IDT* STAC9271D audio codec

•

HD Audio Link header

LAN Support

Intel

82566DC Gigabit (10/100/1000 Mb/s) Ethernet LAN controller

Expansion
Capabilities

•

One PCI Express x16 connector

•

Two PCI Express x1 connectors

•

One PCI connector

Legacy I/O Support

Legacy I/O Controller that provides:

•

Consumer Infrared (CIR) support

•

One serial port via an onboard header

Peripheral
Interfaces

•

Up to 12 USB 2.0 ports

―

Six ports routed to the back panel

―

Six ports routed to three USB headers

•

Up to two IEEE 1394a ports

―

One port routed to the back panel

―

One port routed to an IEEE 1394a header

•

Six Serial ATA (SATA) channels (3.0 Gb/s), via the ICH9R, including
one external SATA (eSATA) channel

•

One IDE interface with ATA-66/100 support (two devices)

continued

Summary of Contents for BLKDG33TLM - G33 Express Socket775 mATX Motherboardw/Video



























































































Search results

Summary of Contents for BLKDG33TLM - G33 Express Socket775 mATX Motherboardw/Video

Reviews:

Brands by name

Popular brands

Intel BLKDG33TLM - G33 Express Socket775 mATX Motherboardw/Video, Product Manual

Search results

Summary of Contents for BLKDG33TLM - G33 Express Socket775 mATX Motherboardw/Video

Reviews:

Brands by name

Popular brands