Intel 848P Thermal Design Manual Download Page 19 | Manualshive

Page: 19 / 35

Intel 848P Thermal Design Manual Download Page 19

Thermal Metrology

R

Intel

®

848P Chipset Thermal Design Guide

19

3.3 Airflow

Characterization

Figure 7 describes the recommended location for air temperature measurements measured relative to
the component. For a more accurate measurement of the average approach air temperature, Intel
recommends averaging temperatures recorded from two thermocouples spaced about 25 mm
[1.0 in] apart. Locations for both a single thermocouple and a pair of thermocouples are presented.

Figure 7. Airflow Temperature Measurement Locations

Airflow velocity should be measured using industry standard air velocity sensors. Typical airflow
sensor technology may include hot wire anemometers. Figure 7 provides guidance for airflow
velocity measurement locations. These locations are for a typical JEDEC test setup and may not be
compatible with chassis layouts due to the proximity of the processor to the MCH. The user may
have to adjust the locations for a specific chassis. Be aware that sensors may need to be aligned
perpendicular to the airflow velocity vector or an inaccurate measurement may result. Measurements
should be taken with the chassis fully sealed in its operational configuration to achieve a
representative airflow profile within the chassis.

«
...
17
18
19
20
21
...
»

Summary of Contents for 848P




































Reviews:

No comments