Intel 81341 Developer'S Manual Download Page 99

Page: 99 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

Address Translation Unit (PCI-X)—Intel

81341 and 81342

2.7

ATU Error Conditions

PCI and internal bus error conditions cause ATU state machines to exit normal

operation and return to idle states. In addition, status bits are set to inform error

handling code of exact cause of error condition. Error conditions and status can be

found in the ATUSR. The basic flow for a PCI error is as follows:

• Set the bit in the ATU Status Register which corresponds to the error condition

(master abort, target abort, etc.)

• Set the bit in the ATU Interrupt Status Register which corresponds to the error

condition (master abort, target abort, etc.). This function is maskable for all PCI

error conditions.

• The setting of the bit in the ATU Interrupt Status Register results in an interrupt

being driven to the Intel XScale

processor.

Error conditions on one side of the ATU are generally propagated to the other side of

the ATU and have different effects depending on the error. Error conditions and their

effects are described in the following sections.
PCI bus error conditions and the action taken on the bus are defined within the PCI

Local Bus Specification, Revision 2.3, and the PCI-X Protocol Addendum to the PCI

Local Bus Specification, Revision 2.0. The ATU adheres to the error conditions defined

within the PCI specification for both requester and target operation. Error conditions on

the internal bus are caused by an ECC error from the Memory Controller, (see

Section

7.5, “ECC Interrupts/Error Conditions” on page 621

for details on memory controller

error conditions), an Internal Bus Byte Parity Error, or by incorrect addressing resulting

in an internal master abort. All actions on the PCI Bus for error situations are

dependent on the error control bits found in the ATU Command Register (see

Section

2.13.5, “ATU Command Register - ATUCMD” on page 153

) for both Conventional and

PCI-X modes. For PCI-X mode, the error response is also dependent on an error control

bit in the PCI-X Command Register (see

Section 2.13.55, “PCI-X Command Register -

PCIXCMD” on page 196

). In addition, for PCI-X Mode 2 only, the error response also

depends on the ECC Control and Status Register (see

Section 2.13.57, “ECC Control

and Status Register - ECCCSR” on page 200

The 81341 and 81342 operates in parity mode (when enabled) for conventional PCI

(PCI-33, PCI-66), and PCI-X Mode 1 (PCI-X 66, PCI-X 133). For PCI-X Mode 2, the

81341 and 81342 functions in ECC mode. Parity errors, single-bit ECC errors (when

correction is disabled), and multi-bit ECC errors are uncorrectable errors. In ECC mode,

all single-bit errors are corrected when error correction is enabled and the transaction

completes.
The following sections detail all ATU error conditions on the PCI and 81341 and 81342

internal bus, action taken on these conditions, and status and control bits associated

with error handling.

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands