Intel 81341 Developer'S Manual Download Page 810 | Manualshive

Page: 810 / 1056

background image

Intel

®

81341 and 81342—Timers

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

810

Order Number: 315037-002US

12.1.3

Load/Store Access Latency for Timer Registers

As with all other load accesses from internal memory-mapped registers, a load

instruction that accesses a timer register has a latency of one internal processor cycle.

With one exception, a store access to a timer register completes and all state changes

take effect before the next instruction begins execution. The exception to this is when

disabling a timer. Latency associated with the disabling action is such that a timer

interrupt may be posted immediately after the disabling instruction completes. This can

occur when the timer is near zero as the store to TMRx occurs. In this case, the timer

interrupt is posted immediately after the store to TMRx completes and before the next

instruction can execute.

summarizes the timer access and response timings.

Refer also to the individual register descriptions for details.
Note that the processor may delay the actual issuing of the load or store operation due

to previous instruction activity and resource availability of processor functional units.
The processor ensures that the TMRx.tc bit is cleared within one internal bus clock after

a load or store instruction accesses TMRx.

Table 493. Timer Responses to Register Bit Settings

Name

Status

Action

(TMRx.tc)

Terminal Count

Bit 0

READ

Timer clears this bit when user software accesses TMRx. This bit can be set 1

internal bus clock later. The timer sets this bit within 1 internal bus clock of

TCRx reaching zero when TMRx.reload=0.

WRITE

Timer clears this bit within 1 internal bus clock after the software accesses

TMRx. The timer ignores any value specified for TMRx.tc in a write request.

(TMRx.enable)

Timer Enable

Bit 1

READ

Bit is available 1 internal bus clock after executing a read instruction from

TMRx.

WRITE

Writing a ‘1’ enables the internal bus clock to decrement TCRx within 1

internal bus clock after executing a store instruction to TMRx.

(TMRx.reload)

Timer Auto Reload

Enable

Bit 2

READ

Bit is available 1 internal bus clock after executing a read instruction from

TMRx.

WRITE

Writing a ‘1’ enables the reload capability within 1 internal bus clock after the

store instruction to TMRx has executed. The timer loads TRRx data into TCRx

and decrements this value during the next internal bus clock cycle.

(TMRx.csel1:0)

Timer Input Clock

Select

Bits 4-5

READ

Bits are available 1 internal bus clock after executing a read instruction from

TMRx.csel1:0 bit(s).

WRITE

The timer re-synchronizes the clock cycle used to decrement TCRx within one

internal bus clock cycle after executing a store instruction to TMRx.csel1:0

bit(s).

(TCRx.d31:0)

Timer Count

Register

READ

The current TCRx count value is available within 1 internal bus clock cycle

after executing a read instruction from TCRx. When the timer is running, the

pre-decremented value is returned as the current value. When the timer is

transferring the TRRx count into TCRx in the current count cycle, the timer

returns the new TCRx count value to the executing read instruction.

WRITE

The value written to TCRx becomes the active value within 1 internal bus

clock cycle. When the timer is running, the value written is decremented in

the current clock cycle.

(TRRx.d31:0)

Timer Reload

Register

READ

The current TRRx count value is available within 1 internal bus clock after

executing a read instruction from TRRx.

WRITE

The value written to TRRx becomes the active value stored in TRRx within 1

internal bus clock cycle. When the timer is transferring the TRRx value into

the TCRx, data written to TRRx is also transferred into TCRx.

«
...
808
809
810
811
812
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

Brand: Magnat Audio Pages: 2

Brand: Data Translation Pages: 60

Brand: Ubiquiti Pages: 23

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Brand: Advantech Pages: 36

Brand: SurfControl Pages: 2

Brand: AOpen Pages: 18

CNPS5X PERFORMA

Brand: ZALMAN Pages: 8

Brand: Symantec Pages: 100

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

Brand: Digital Voice Systems Pages: 32

N-FXE 02B Series

Brand: Lantronix Pages: 10

Brand: IBM Pages: 168

Brand: HighPoint Pages: 12

Sporlan Division SCS-PB Series

Brand: Parker Pages: 10

Brand: Transition Networks Pages: 1

GPX-N 1080Ti-M23

Brand: Alphacool Pages: 4

Brand: Crown Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands