Intel 81341 Developer'S Manual Download Page 247 | Manualshive

Page: 247 / 1056

background image

Intel

®

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

247

Address Translation Unit (PCI Express)—Intel

®

81341 and 81342

3.3.1.4

Inbound I/O Cycle Translation

Inbound address window 2 can be configured to accept I/O Read and I/O Write

transactions by setting the Memory/IO space indicator bit to 1 in the

Base Address Register 2 - IABAR2” on page 314

. All I/O cycles are 32-bit transactions

(DWORD).
For inbound I/O reads, the INPQ is used in the same manner as inbound memory read

operations and the exception cases are identical. However, the internal bus cycle that

results is always be a 32-bit transaction.
For inbound I/O writes, the ATU uses the INPHQ to hold both the header and the INPDQ

to hold the data. An I/O write TLP with poisoned data results in the data being dropped

and a Completion with Completions status of UR is returned to the requester.
When there are no errors during the request cycle, transaction ordering and priority are

satisfied. Next, the internal bus master interface requests the internal bus and deliver

the write data to the target as defined in

Section 3.3.1.2

.

The status of the transaction on the internal bus is returned to the requestor on the PCI

Express Link. When the Write Cycle Master Aborts on the Internal Bus, a Completion

with status of Completer Abort is returned.

3.3.1.5

Inbound Configuration Cycle Translation (ID Routed)

The 81341 and 81342 ATU only accepts Type 0 configuration requests with a function

number of zero when bit 7 of the ATUHTR (see

Section 3.16.11, “ATU Header Type

Register - ATUHTR” on page 306

) is cleared or function numbers of zero and one when

bit 7 of the ATUHTR is set.
The ATU is a native PCI Express device that supports both the standard PCI express

capability structure and the PCI Express Extended capability structure. The ATU

configuration space is selected by any PCI Express Type 0 configuration cycle targeting

function 0. The bus number and device number is captured from all valid Type 0

configuration write TLPs that target an enabled function.
For inbound configuration reads, the INPQ is used in the same manner as inbound

memory read operations.
For inbound configuration writes, the ATU uses the INPQ to hold both the header and

the data. An configuration write TLP with poisoned data results in the data being

dropped and an Completion with Completions status of UR is returned to the requester.
When there are no errors during the request cycle, transaction ordering and priority are

satisfied. Next, the internal bus master interface requests the internal bus and deliver

the write data to the target as defined in

Section 3.3.1.2

.

Since Master Aborts and Target Aborts cannot occur during configuration cycles on the

internal bus, a Completion TLP with Successful Completion (SC) status is generated for

all configuration cycles.
When the Configuration Request Retry bit is set (PCSR[2)], the Configuration Request

cycle is terminated with a Configuration Request Retry Status (CRS).

«
...
245
246
247
248
249
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Power Control Processor

Brand: ETC Pages: 64

Core 2 Quad Q9400

Brand: Intel Pages: 2

Brand: QuickLink Pages: 8

Brand: S&T Pages: 28

See3CAM 30 Z10X

Brand: e-con Systems Pages: 14

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brand: ETAS Pages: 29

Brand: Extron electronics Pages: 19

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

Internal All-in-One Digital Media Drive ULT31793

Brand: Ultra Products Pages: 1

Q-SYS QIO-GP8x8

Brand: QSC Pages: 13

ROADRECORDER 8400 NVR

Brand: Safety Vision Pages: 27

Brand: MACHINIST Pages: 15

Brand: peplink Pages: 111

Brand: Alpine Pages: 17

Brand: ekwb Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands