Intel 81341 Developer'S Manual Download Page 111 | Manualshive

Page: 111 / 1056

background image

Intel

®

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

111

Address Translation Unit (PCI-X)—Intel

®

81341 and 81342

2.7.3.10 Split Completion Messages

As a target, the ATU may encounter this error when operating in the PCI-X mode.
Uncorrectable Data errors occurring during Split Completion Messages claimed by the

ATU may assert

PERR#

(when enabled) or

SERR# (when

enabled) on the PCI Bus.

When an error occurs, the ATU accepts the data and complete normally. Specifically,

the following actions with the given constraints are taken by the ATU:

•

PERR#

is asserted three clocks cycles following the data phase in which the

uncorrectable data error is detected on the bus. This is only done when the Parity

Error Response bit in the ATUCMD is set. When the ATU asserts

PERR#

, additional

actions are taken:

— The Master Parity Error bit in the ATUSR is set.

— When the ATU PCI Master Parity Error Interrupt Mask Bit in the ATUIMR is clear,

set the PCI Master Parity Error bit in the ATUISR. When set, no action.

— When the

SERR#

Enable bit in the ATUCMD is set, and the Uncorrectable Data

Error Recover Enable bit in the PCIXCMD register is clear, assert

SERR#

;

otherwise no action is taken. When the ATU asserts

SERR#,

additional actions

are taken:

Set the

SERR#

Asserted bit in the ATUSR.

When the ATU

SERR#

Asserted Interrupt Mask Bit in the ATUIMR is clear, set

the

SERR#

Asserted bit in the ATUISR. When set, no action.

When the ATU

SERR#

Detected Interrupt Enable Bit in the ATUCR is set, set

the

SERR#

Detected bit in the ATUISR. When clear, no action.

• When the SCE bit (Split Completion Error -- bit 30 of the Completer Attributes) is

set during the Attribute phase, the Received Split Completion Error Message bit in

the PCIXSR is set. When the ATU sets this bit, additional actions are taken:

— When the ATU Received Split Completion Error Message Interrupt Mask bit in

the ATUIMR is clear, set the Received Split Completion Error Message bit in the

ATUISR. When set, no action.

• The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit,

additional actions are taken:

— When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear,

set the Detected Parity Error bit in the ATUISR. When set, no action.

• For PCI-X Mode 2, update the

“ECC Control and Status Register - ECCCSR” on

“ECC First Address Register - ECCFAR” on page 203

Second Address Register - ECCSAR” on page 204

, and the

“ECC Attribute Register -

ECCAR” on page 205

for the transaction.

• The transaction associated with the Split Completion Message is discarded.

• When the discarded transaction was a read, the read completion is aborted on the

internal bus of the 81341 and 81342.

«
...
109
110
111
112
113
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

Brand: Harman Kardon Pages: 66

Brand: Jabra Pages: 15

Brand: Salusfin Pages: 6

Brand: Ubiquiti Pages: 3

Brand: GAMDIAS Pages: 15

Brand: Profile Pages: 6

Brand: Zoom Pages: 88

Brand: M86 Security Pages: 309

Brand: AOpen Pages: 18

Brand: B&B Electronics Pages: 17

Brand: Laser Pages: 4

Brand: JAKA Pages: 37

H8S/2646 Series

Brand: Renesas Pages: 20

Brand: Intel Pages: 20

Brand: Cypress Semiconductor Pages: 38

Brand: Zonet Pages: 1

FiberTwist XGS2410

Brand: Genexis Pages: 7

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands