Intel 80331 Design Manual Download Page 60

Page: 60 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.14

PCI 66 MHz Slot Topology

Figure 29

and

Table 21

provides routing details for a topology with for an PCI 66 MHz design with

slots.

Trace Length TL3, TL4,
between connectors

0.8” minimum - 1.4” maximum

Trace Length TL_EM1 from
the first PCI connector to the
embedded device.

1.0” minimum - 3.5” maximum

Trace Length TL_AD1,
TL_AD2, TL_AD3 from PCI
connector to the Receiver

0.75” minimum - 1.5” maximum

1.75” minimum - 2.75” maximum

Length Matching
Requirements:

No length matching is required among datalines. For length matching for clocks,
refer clock guidelines

Table 8

Number of vias

Four vias maximum

Table 20.

PCI-X 66 MHz Mixed Mode Routing Recommendations (Sheet 2 of 2)

Figure 29.

PCI 66 MHz Topology

Table 21.

PCI 66 MHz Slot Table (Sheet 1 of 2)

Parameter

Routing Guideline for AD

Bus

Routing Guideline for

Upper AD Bus

Reference Plane

Route over an unbroken ground plane

Breakout

5 mils on 5 mils spacing. Maximum length of the
breakout is 500 mils.

Motherboard Trace Impedance (microstrip and
stripline)

50 Ohms +/- 15%

Add-in card Impedance (microstrip and stripline)

60 Ohms +/- 15%

Stripline Trace Spacing

10 mils, from edge to edge

Microstrip Trace Spacing

15 mils, from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum
edge-to-edge

Trace Length 1 TL1: From 80331 signal Ball to first
connector

1.0” minimum - 7.0” maximum

1.0” minimum - 7.0”
maximum

Trace Length TL2 between connectors

0.8” minimum - 1.2” maximum

TL1

CONN1

L_A

TL2

CONN2

L_A

AD1

AD2

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands