Intel 80331 Design Manual Download Page 58

Page: 58 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.12

PCI-X 66 MHz Embedded Topology

Figure 27

and

Table 19

provides routing details for a topology with for an embedded PCI-X

66 MHz application.

Trace Length TL_AD1 to
TL_AD4 - from junction to
connector to receiver

0.75” minimum - 1.5” maximum

1.75” minimum - 2.75” maximum

Length Matching
Requirements:

No length matching is required among datalines. For length matching for clocks,
refer clock guidelines

Table 8

Number of vias

Four vias maximum

Table 18.

PCI-X 66 MHz Slot Routing Recommendations (Sheet 2 of 2)

Figure 27.

PCI-X 66 MHz Embedded Routing Topology

Table 19.

PCI-X 66 MHz Embedded Routing Recommendations (Sheet 1 of 2)

Parameter

Routing Guideline for AD Bus

Reference Plane

Route over an unbroken ground plane

Breakout

5 mils on 5 mils spacing. Maximum length of the breakout is 500 mils.

Motherboard Trace
Impedance (microstrip and
stripline)

50 Ohms +/- 15%

Add-in card Impedance
(microstrip and stripline)

60 Ohms +/- 15%

Stripline Trace Spacing

12 mils, from edge to edge

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands