BASIC OPERATION - USER MODE
When radio is turned ON, it always sets in the USER MODE. In this mode, user can only operate the following basic functions, in
order to avoid entering any wrong command or change the radio settings and programming.
Power ON/OFF
1.
Switch ON the radio by pressing and holding the ON-OFF (8) key for about 2 seconds.
2.
The LCD Display (9) will shortly show the Channel Number (A) and the CTCSS Code Number (B).
3.
Then the LCD Display (9) will show the selected Volume Level (A) (from level 01 to 08), the Battery Level (G) and the Keypad
Lock icon (E).
4.
To switch OFF the radio, press and hold the ON-OFF (8) key for about 2 seconds.
Volume Level Setting
Adjust the Volume to the desired level, pressing the UP (3) or DOWN (4) keys while listening to an incoming communication.
The desired Volume Level (A) will appear on the LCD Display (9).
Monitor Function
Press and hold the MENU/MONITOR key (7) for about 2 seconds to activate the Monitor function. This function opens temporarily
the Squelch in order to listen to the background noise and to any weak signal. This function is convenient to monitor any incoming
communication on the operating channel. If the Monitor function is enabled, the BUSY Icon (C) appears on the LCD Display (9). To
disable the Monitor function, release the MENU/MONITOR key (7).
Earset Operation
1.
Connect the external earset to the earset jack (1).
2.
Adjust the Volume to the desired level.
3.
The built-in speaker (5) is disabled when the earset is connected.
Always set the volume to the minimum level before connecting an external earset, in order to avoid damaging the earset or the
user’s ear. Gradually increase the volume level while wearing the earset and listening to an incoming signal.
CALL Function / CALL Memory
The Pager can receive and store in memory an incoming CALL signal, if this CALL signal was transmitted by a
transmitter/transceiver type DRS-5070 (desk type station) or SL-02 (handheld station).
When a CALL signal is received, a CALL tone is heard and the CALL icon (F) blinks on the LCD (9). The CALL icon (F) will
continue to blink in order to inform the user that a CALL signal was received by its pager and it will stop blinking when the
MENU/Monitor key (7) will be pressed.
ADVANCED FUNCTIONS - PROGRAM MODE
Pager may be programmed by the system manager in the PROGRAM MODE. The following functions are programmable only in
the PROGRAM MODE. In the normal USER MODE, the user cannot access, program or modify any of these functions, in order to
avoid entering any wrong command or change the settings programmed by the system manager.
1.
Channel selection (PMR channels P1-P8) (LPD channels 01-69)
2.
CTCSS Code selection (from 0 to 38)
3.
VIBRATION Alert
To enter the PROGRAM MODE, proceed as follows :
1.
Switch OFF the radio.
2.
Switch ON the radio by pressing simultaneously the ON-OFF (8) and the MENU/MONITOR (7) keys, until radio is ON.
3.
The Keypad LOCK icon (E) will disappear from the LCD (9).
4.
Press the MENU/Monitor (7) key several times to scroll the various programmable functions.
Switch OFF the radio to exit the PROGRAM MODE.
Channel Selection
1.
In the PROGRAM MODE press the MENU/Monitor Key (7) until the Channel Number (A) blinks on the LCD (9).
2.
Press the UP (3) or DOWN (4) keys to select the desired channel number (PMR channels P1-P8) (LPD channels 01-69).
Press and hold the UP (3) or DOWN (4) key, to advance the channel selection quicker.
3.
To confirm and store the selection, press the ON-OFF (8) key or press the MENU/Monitor (7) key to move to the next function.
LPD Channels Table
PMR Channels Table
