Installing and connecting the supplied mobile Magnet Antenna
A 27 MHz mobile antenna with magnet base and 4m RG-58/U is included in the kit. Please
pay attention to correctly placing the magnet antenna on the vehicle top. The magnet
antenna must be firmly attached to the vehicle metal body. Before attaching the antenna on
the car body, carefully clean both the bottom side of the antenna base and the car body
surface. Connect the antenna connector (D) to the antenna outlet (11) located on the rear
side of the radio. Antenna must be usually placed on the highest part of the vehicle, free
from nearby metal parts and as far as possible from any possible source of electric or
electromagnetic noice. The antenna cable must not be damaged in its way to the radio.
Parts description
A.
Whip
Whip with protective rubber cup.
B.
Magnet base
Antenna magnet base to be placed on any iron
or steel surface, with no need to drill any hole
on the vehicle body.
C.
RG-58/U Cable
RG-58/U cable, 4m long.
D.
RF Connector
RCA connector.
Connect to the antenna outlet (11), located on
the rear side of the radio.
FREQUENCY BANDS TABLE
The receiver INTEK CBM-450 includes an advanced multi-standard programmable circuit,
which allows to program different frequency bands, specifications and operating modes, in
conformity with the regulations in the country where the product is used. 9 programmable
frequency bands are available, as per the below table :
FREQUENCY BAND SELECTION / PROGRAMMING
The receiver has to be programmed on the CB frequency band used in the country where
the product is used. When radio is switched ON, the current programmed frequency band
code will be displayed (blinking) for about 3 seconds.
To program a different frequency band, proceed as follows :
1) Turn OFF the radio.
2) Press and keep pressed the UP key (6), then turn ON the radio using the
OFF/VOLUME knob (9).
3) The current frequency band code (B) will blink on the LCD display (4).
4) Now select the new desired frequency band code by pressing the UP (6) or DN (5) key.
5) Wait for about 5 seconds to confirm and store the new selected frequency band code.
UK/CE CHANNELS SELECTION (FREQUENCY BAND "U")
The "U" band (UK/CE band) includes both UK and CE channels, this band is for use in the
UK. If a UK channel is selected, the display (4) will show the channel number (B) and the
indication "U". If a CEPT channel is selected the display (4) will show the channel
number (B) and the indication "C".
SPECIFICATIONS
General
Channels
Refer to the frequency bands table
Frequency range
27 MHz Citizen Band
Frequency control
P.L.L.
Operating temperature
-10°/+55°C
DC input voltage
13.2Vdc ±15%
Size / Weight
115 (L) x 43 (H) x 165 (D) mm / 350 gr.
Receiver
System
Double conversion, CPU controlled super-heterodine
IF
1° 10.695 MHz / 2° 455 KHz
Sensitivity 0.5µV
Audio output
2.5W - 8% distortion at 1 KHz
Current drain
350mA (stand-by)
USER INFORMATION
In accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15
”Implementation of Directives 2002/95/EC, 2002/96/EC and 2003/108/EC, relative to
reduction of the use of hazardous substances in electrical and electronic equipment, in
addition to waste disposal”.
The crossed bin symbol shown on the equipment indicates that at the end of its
working life the product must be collected separately from other waste.
The user must therefore take the above equipment to the appropriate
differentiated collection centres for electronic and electro technical waste, or
return it to the dealer when purchasing a new appliance of equivalent type, in a
ratio of one to one.
Appropriate differentiated waste collection for subsequent recycling, treatment and
environment-friendly disposal of the discarded equipment helps to prevent possible
negative environmental and health effects and encourages recycling of the component
materials of the equipment.
Illegal disposal of the product by the user will be punished by application of the
administrative fines provided for by the legislative decree no. 22/1997 (article 50 and
following of the legislative decree no. 22/1997).
DECLARATION OF CONFORMITY
A
C
D
B
FREQUENCY BAND
ID CODE
COUNTRY
SPECIFICATIONS
(Channels, Operating Modes)
E1
ITALY/SPAIN
40CH AM / FM
I2
ITALY
36CH AM / FM
dE
GERMANY
80CH FM - 12CH AM
d2
GERMANY
40CH FM - 12CH AM
EU
EUROPE/FRANCE
40CH FM - 40CH AM
CE
CEPT
40CH FM
U
UK
40CH FM UK FREQUENCIES
40CH FM CEPT FREQUENCIES
PL
PD
POLAND
POLAND
40CH AM / FM POLISH FREQUENCIES
40CH AM / FM POLISH FREQUENCIES
With the present declaration, we certify that the following products :
INTEK CBM-450
comply with all the technical regulations applicable to the above mentioned products
in accordance with the EC Directives 2006/95/EC, 2004/108/EC, 99/5/EC.
Type of product :
CB Receiver
Details of applied standards :
EN 300 433-1/-2, EN 300 135-1/-2
EN 301 489-1, EN 301 489-13
EN 60065
Manufacturer :
INTEK S.R.L.
Via G. Marconi, 16
20090 Segrate, Italy
Tel. 39-02-26950451 / Fax. 39-02-26952185
E-mail : [email protected]
Segrate, 19/12/2011
dr. Vittorio Zanetti
(General Manager)
DECLARATION OF CONFORMITY
WARNING !!!
The Magnet Antenna included in this set has been designed
to withstand a vehicle speed of maximum 130 km/h (no front
wind condition). Do not exceed this speed when the antenna
is installed, to prevent antenna from being torn away from
the vehicle and causing possible damage to other drivers !
CH
RoHS
2002/95/EC
