Integral Audio 1101S Installation Manual Download Page 6

6  |  Integral Audio  |  Installation Instructions  

Continued on next page...

9.  d

etacH

 d

rIVerS

 S

eat

 b

elt

Remove the Torx T-50 bolt.  Remove the metal rod 

that secures the bottom of the seat belt.

15.  f

ISH

 p

ower

 w

Ire

 t

HrougH

 f

Irewall

Locate the wire pass-thru grommet in the upper left 

of the area behind the knee bolster (just above and 

left of the top of the clutch pedal, if present).  Feed 

your electrician’s fish tape through this grommet and 

into the engine compartment.  Locate the fish tape 

(see item (1) from the next step).  Tape the end of the 

power wire to the fish tape and pull it into the cabin.

16.  I

nStall

 f

uSe

 H

older

 (p

art

 1)

Mount the fuse holder to a suitable location on the 

wall of the compartment area (1) using two #6 x ½” 

Stainless Hex Washer Head Self-tapping screws.
Remove the battery cover (2).  Determine the routing 

of the power wire to the battery.  You may need to drill 

a small hole in the plastic bulkhead.

14.  p

ull

 d

own

 

tHe

 K

nee

 b

olSter

Pull in and down firmly on the top of the Knee Bolster 

(the panel under the steering wheel) to release the 

top.  Lift each outer edge to release the hinges.  

Remove and set aside.

12.  r

eMoVe

 l

eft

 d

oor

 S

Ill

 t

rIM

 (

part

 3)

[Seat shown removed for clarity]
Remove the door seal over the entire length of the 

right door sill by lifting it up and off.  Pull Door Sill 

Panel (2) inward, releasing clips (3).  This requires 

a firm pull at each of the clip locations.  Remove the 

small trim piece (1) by pulling it toward the rear of the 

vehicle, releasing spring clip.

11.  r

eMoVe

 l

eft

 d

oor

 S

Ill

 t

rIM

 (

part

 2)

Remove the expansion rivet (1) from the front of the 

Door Sill (in the footwell area).  Pull firmly inward all 

along the 

B.  RUN THE POWER & GROUND WIRES

10.  r

eMoVe

 l

eft

 d

oor

 S

Ill

 t

rIM

 (

part

 1)

The top of the Left Rear Interior Panel locks over the 

Left Door Sill Trim and must be released to remove 

the Door Sill.  Pull inward firmly on the bottom of the 

front of the Left Rear Panel, releasing the friction clips 

(1) for just this portion.  It is not necessary 

13.  r

eMoVe

 

tHe

 r

IgHt

 d

oor

 S

Ill

 t

rIM

Repeat the previous three steps for the Right Side of 

the vehicle.

See Previous 

Images

Summary of Contents for 1101S













Reviews: