background image

 
 

 
____________________________________________________________________________________________

 

(091214_Sp) Integra EPRO 1K-3K

 

 - 

7

 

First Time:  

CHARGE BATTERIES FOR 6 HOURS BEFORE CONNECTING YOUR EQUIPMENTS TO UPS 

 

 
3. INSTALATION 

 
 

 
 

 

This product leaves factory with battery fully charged, however during transportation and storage it may loose a 

non determined part of its charge; therefore we recommend plugging it to Power Line for 6 hours before using the 
UPS. 

 

Install this unit in any protected environment with a dust free air flow. Also corrosive vapours and conductive 

contaminants must be avoided. Do not use UPS outdoors or where either temperature or humidity exceeds tech 
specs. Install UPS at least 10 inches away from your monitor to avoid magnetic interference. 

 

1.- Plug input AC power cord to an appropriate power outlet with Line-Neutral-Ground contacts.  

 
2.-  First time leave UPS recharging batteries during 6 hours  before connecting your devices to the UPS  to  let 

batteries recover charging level to offer full battery backup time. 
 

3.- Connect your devices to be protected to UPS outlets. Take care to not overload UPS output by connecting 
devices with higher power ratings than UPS power capacity. Laser printers, scanners and copiers frequently have 

two  different  power  ratings:  in  stand-by  power  ratings  are  very  low  compared  with  consumption  rating  during 
operation. If this kind of products will be connected to the UPS operation power rating must be considering to size 

total power consumption to be connected to UPS. 
 

4.- EPO Function: Emergency Power Off function allows to power off UPS outlets when EPO input is open. When 
EPO port is closed EPO function is disable. When EPO function is activated UPS will perform following actions: 

 
a) Power Off all outlets,  

b) Switch to STAND-BY mode, 
c) Acoustic alarm is activated as continuous beep 

d) Warning message Nº 20 is indicated on LCD. 
To disable EPO mode and recovering normal mode contact switch or jumper in EPO port must be closed and UPS 

must be powered On by selecting ON push button. 
 

 
EXTERNAL BATTERIES OPTION 

EPRO models  with  EX  mark  (like  EPRO  3K-EX or  EPRO-RACK 3K-EX) are able  to be  connected  to external 
battery cabinets (EX-BATT) to offer longer backup times. 

This kind of models has internal batteries as other EPRO models but they can also be connected at any moment 
to EX-BATT supplied by INTEGRA. 

Special cables to connect EX-BATT to UPS are supplied inside the box of EX-BATT. 

 

INSTRUCTIONS TO CONNECT EXTERNAL BATTERIES 

1)

 

Place EX-BATT case close to UPS. Only INTEGRA approved EX-BATT can be connected to UPS EX 

series. 

2)

 

Check DC breakers are in OFF position (circuit OPEN)  

3)

 

Connect UPS to first EX-BATT using INTEGRA approved DC cable. 

4)

 

If more than one EX-BATT will be connected, then connect first EX-BATT to second EX-BATT and so 

on in that way to other EX-BATT. 

5)

 

After all EX-BATT are connected, switch to ON position all DC breakers located in EX-BATT. 

 

 

Summary of Contents for EPRO-Rack1K-3K






















Reviews: