background image

7

Step 1:

 Connections

Connecting the Subwoofer

Up to four subwoofers with built-in power amplifier can 
be connected to the subwoofer jacks. Set the cut-off 
filter selection switch of the subwoofer to DIRECT. If the 
subwoofer does not have a cut-off filter selection switch 
but has a cut-off frequency adjusting dial, turn it to the 
maximum frequency.

Subwoofer with built-in 
power amplifier

r

The speaker setting is 7.2 ch at the time of purchase. You 
can change it manually or by using automatic speaker 
setting.

r

Short-circuiting the + cable and - cable or contacting the 
cable core to the rear panel of the unit may cause failure. 
Also do not connect two or more cables to one speaker 
terminal or one speaker to several terminals.

r

Using a speaker with less impedance than the setting 
may result in failure.

When using commercially available banana plugs

: tighten 

the speaker terminals to the end and then insert the banana 
plugs. Do not insert the cable core directly into the hole for 
banana plug of speaker terminal. (North American model)

3

Other connections

AM/FM Antenna Connections

Connect the antennas to listen to AM/FM broadcast. When 
listening to the broadcast for the first time, adjust the 
antenna position and orientation to get the best reception.

AM loop 

antenna

(supplied)

Indoor FM antenna 
(supplied)

Fix with a tack on 
the wall.

(North American models)

(Australian models)

Assemble the AM loop antenna (supplied).

Network Connection

You can enjoy Internet radio and DLNA by connecting the 
unit to LAN. The unit can be connected to the router with an 
Ethernet cable. Connect the Ethernet cable to the Ethernet 
port. 

Internet radio

Router

PC

NAS

Headphones Connection

%QPPGEVUVGTGQJGCFRJQPGUYKVJCUVCPFCTFRNWI|KPEJ
QTÔ|OOVQVJG2*10'5LCEMQPVJGHTQPVRCPGN

Sound from the speakers will be off while you are using the 
headphones.

r

If you selected any other listening mode than Stereo, 
Mono and Direct, connecting headphones will switch the 
listening mode to Stereo.

Summary of Contents for DTR-60.6

























Reviews: