background image

21

Then turn the jog dial or press the   or   cursor
button on the remote controller to set whether
or not surround speakers are connected and, if
they are connected, their size.

NONE: 

Select if no surround left and right speakers are connected.

LARGE: 

Select if the surround left and right speakers are large

sized.

SMALL: 

Select if the surround left and right speakers are small

sized.

• If “SMALL” is selected for the Front setting, then “LARGE”

cannot be selected for this setting.

Pressing the jog dial again or   cursor button returns you to the
subwoofer setting.

8. Press the Return (RETURN) button.

You return to the “SPEAKER CONFIG?”
display.

Notes

:

• If you press the Return (RETURN) button again, you go back up one

more level.

• To exit the setup mode immediately, press the Setup (SETUP)

button.

Then turn the jog dial or press the   or   cursor
buttons on the remote controller to set whether
or not a center speaker is connected and, if one
is connected, its size.

NONE: 

Select if no center speaker is connected.

LARGE: 

Select if the center speaker is large sized.

SMALL: 

Select if the center speaker is small sized.

• If “SMALL” is selected for the Front setting, then “LARGE”

cannot be selected for this setting.

7. Press either the jog dial or the 

cursor button on the remote controller
once.

Then turn the jog dial or press the   or   cursor
button on the remote controller to set the size of
your front speakers.

LARGE:

 Select if the front speakers are large sized.

SMALL: 

Select if the front speakers are small sized.

 • If “NO” is selected for the Subwoofer setting, then this setting is

fixed to “LARGE”.

6. Press either the jog dial or the 

cursor button on the remote controller
once.

5. Press either the jog dial or the 

cursor button on the remote controller
once.

2. Press the jog dial or ENTER button on

the remote controller.

Speaker Configuration

These settings tell the DTR-5.2 which speakers you have connected
and what size they are.

1. Press the Setup (SETUP) button.

Speaker setup

Setup

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

3. Press the jog dial or ENTER button on

the remote controller.

4. Turn the jog dial or press the   or 

cursor buttons on the remote
controller to set whether or not a
subwoofer is connected.

YES: 

Select when a subwoofer is connected.

NO: 

Select when a subwoofer is not connected.

* If the indicators directly to the left and right of the jog dial are lit,

turning the jog dial changes the setting of the currently selected
parameter and pushing the jog dial displays the next parameter.

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

Push To Enter

DSP / Mode ADJ

If anything other than “1. SPEAKER SETUP”
appears, turn the jog dial or press the   and 
cursor buttons on the remote controller until
“1. SPEAKER SETUP” appears.

Push To Enter

DSP / Mode ADJ

Return

Setup

RETURN

ENTER

SETUP

Standby/On

Standby

Power

On

O f f

Phones

DVD

Video 2

Video 1

Video 3

Bass

Treble

Master Volume

Smart Scan Navigator

Dimmer

Display

Tuning

FM Mode

Preset Memory

Preset

VCR

Audio

Selector

Tape

FM

AM

Phono

CD

Push To Enter

DSP/ Mode ADJ

Setup

Return

CH Level

A

B

Speakers

HOME THEATER CONTROLLER

RC-441M

Jog dial and indicators

Follow the steps below before you start operating the unit.

DTR-5.2

Remote

controller

Return

The display changes as follows: “1. SPEAKER SETUP” 

  “2.

INPUT SETUP” 

 “3. PREFERENCE.”

* If the indicators directly above and below the jog dial are lit,

turning the jog dial selects a group of settings and pushing the jog
dial enters the selected group (i.e. takes you one level down).

Summary of Contents for DTR-5.2





















































Reviews: