www.urcsupport.com
13
7.
To search for the codes of your other devices,
repeat steps 1 through 6, but substitute the
appropriate key (e.g.,
VCR, DVD, AUD,
or
STB
)
for the device you are searching for.
CHECKING THE CODES
If you have set up your remote control by searching for
your device code (on the previous page), you may need
to find out which four-digit code is operating your
equipment.
For example, to find out which code is operating your TV:
5.
To check for other device codes, repeat steps 1
through 4, but substitute the appropriate key
(e.g.,
VCR, DVD, AUD,
or
STB
) for the device
you are checking. Write down the codes in the
appropriate boxes on page 11.
NOTE:
In the search mode, the remote control will
send IR codes from its library to the selected
device, starting with the most popular code
first.
6.
Press
POWER
. The TV should turn on, then
press
SETUP
once to lock in the code. The LED
will blink twice to indicate that the code is
saved.
NOTE:
If the TV does not turn on during step 6, then
slowly press and release
CH-
to go back
through the codes, then press
SETUP
when the
TV turns on.
1.
On the remote control, press
TV
once; it will
blink once. Then press and hold
SETUP
until
the
TV
key blinks twice.
2.
Enter
9 9 0
. The
TV
key will blink twice.
3.
To view the code for the first digit, press
1
once. Count the number of times the
TV
key
blinks (e.g., 3 blinks = 3) and write down the
number in the leftmost TV Code box on
page 11.
NOTE:
If a code digit is 0, the selected mode key will
not blink.
4.
Repeat step 3 three more times for the
remaining digits. Use
2
for the second digit,
3
for the third digit, and
4
for the fourth digit.
Finish writing down the code in the TV Code
boxes on page 11.
Nebula Potenza ST.fm Page 13 Monday, October 15, 2007 4:55 PM
www.urcsupport.com
14
USING LEARNING
The Potenza ST Universal Remote Control includes a
Learning feature (not available on all models) so you
can add functions that are unique to your home
entertainment devices (e.g.,VCR Tracking Up or Down).
However, there are some considerations.
Learning Precautions
•
Your original remote controls must be in working
order for learning to work properly.
•
Learned keys are mode-specific, so each one can
store a unique function for each mode.
•
Do not use the following keys for learning:
Device
Keys, SETUP, Record (•), Tune-In Keys
.
•
Learning capacity is approximately 16 to 25 keys,
depending on the code being learned.
•
Certain device functions are not learnable including
multi-frequency types, some high frequency ones,
and other unusual formats.
•
For optimum learning, avoid high levels of ambient
light such as natural sunlight or energy-efficient
fluorescent lights.
NOTE:
Please have your original remote controls
handy before programming learning.
Programming a Learned Key
NOTE:
If more than 15 seconds pass between key
presses, the remote exits programming.
3.
Press the desired key on the Potenza ST once
to store the feature to be learned.
1.
Press and hold
SETUP
until the last-selected
mode key blinks twice, then press
9 7 5
.
NOTE:
If the LED displays one long flash instead,
either your batteries are low, or the Potenza ST
Universal Remote Control has a memory fault.
2.
Press a mode key once (i.e.,
VCR, DVD, AUD,
TV,
or
STB
) to assign a mode for learning.
Nebula Potenza ST.fm Page 14 Monday, October 15, 2007 4:55 PM
www.urcsupport.com
15
4.
Place the Potenza ST Remote Control head-to-
head (about 2" apart) from your original
remote control. Also locate the key (on your
original remote control) that you want the
Potenza ST Universal Remote Control to learn.
5.
On the original remote, press and hold the key
to be learned. The Potenza ST Remote
Control’s LED will blink rapidly, then turn off.
Continue holding the key on the original
remote until the LED blinks twice.
NOTE:
If the LED displays one long blink, a learning
error has occurred. Try repeating this step
again until a successful capture occurs. If the
function is
still not captured, press and hold
SETUP
to exit programming and review the
“Learning Precautions” on the previous page.
If needed, also see “Troubleshooting” on
page 24. After review, start programming
again at step 1.
Deleting a Single Learning Key
This process returns the key to its original programming
for the mode you select. You can also delete learned
programming by teaching a different function to the key
(see “Programming a Learned Key” on page 14)
NOTE:
If more than 15 seconds pass between key
presses, the remote exits programming.
6.
Repeat steps 2 through 5 for another mode
and/or key or press and hold
SETUP
until the
active mode key LED blinks twice to exit
programming.
1.
Press and hold
SETUP
until the last-selected
mode key blinks twice, then press
9 7 6
.
2.
Press a mode key once (i.e.,
VCR, DVD, AUD,
TV,
or
STB
). The LED on the selected mode
key will blink once.
2"
Nebula Potenza ST.fm Page 15 Monday, October 15, 2007 4:55 PM