Intech Instruments IN-P Series Installation Manual Download Page 5

 

5

 

 

4.1 

 

Position your input jumpers: 

 

The IP07 input module has one jumper, which may need to be repositioned to suit your application. When you have  

finished, slide the input module back into the case and replace the plastic backing plate. 

 

 

 

JUMPER POSITIONING: 

 

 

 

 

 

 

 

 

Example showing a Jumper In & Jumper Out:

 

 

 

 

 

Before you begin:

 

Once the backing plate has been removed, gently slide the input 

module from the case (see Section 3.2J to identify the input module). 

SECTION 4. –

 

Input Jumper Configuration. 

Before you Begin: 

Before you can begin wiring, the IP07 input module must be removed from the meter case so that the jumpers can be 

positioned for your input type. Remove the plastic backing plate from the rear of the meter by inserting a screwdriver into 

the indents circled on the image below: 

20mA     

Current input (0~20mA or 

4~20mA).

 

Custom 

Custom input – call for options.

 

2V          

Voltage input (0~2V).

 

Jumper In 

Jumper Out (i.e. Jumper not fitted). 

CONNECTOR PINS: 

G - Relays 

Wiring: Section 5.3 

H - Serial port 

Wiring: Section 5.5 

I - Analogue output 

Wiring: Section 5.4 

J - IP07 input module 

Jumper setup:  Section 4 

 

Wiring: Section 5.2 

K - Function pins 

Wiring: Section 5.6 

L - Power supply (HV LV)  

Wiring: Section 5.1 

3.2 

 

Fig 2 - Rear view: 

Summary of Contents for IN-P Series













Reviews: