background image

- GB.2-V1 - 

WARNING

 

1.

 

Working in the vicinity of a lead acid battery is dangerous. 
Batteries generate explosive gases during normal battery 
operation. For this reason, it is of utmost importance, if 
you have any doubt, that each time before using your 
tester, you read these instructions very carefully. 

2.

 

To reduce risk of battery explosion, follow these 
instructions and those published by the battery 
manufacturer and manufacturer of any equipment you 
intend to use in the vicinity of the battery. Observe 
cautionary markings on these items.

 

3.

 

Do not expose the tester to rain or snow.

 

 

PERSONAL SAFETY PRECAUTIONS

 

1.

 

Someone should be within range of your voice or close 
enough to come to your aid when you work near a lead 
acid battery.

 

2.

 

Have plenty of fresh water and soap nearby in case 
battery acid contacts skin, clothing or eyes.

 

3.

 

Wear safety glasses and protective clothing.

 

4.

 

If battery acid contacts skin or clothing, wash 
immediately with soap and water. If acid enters eye, 
immediately flood eye with running cold water for at least 
ten minutes and get medical attention immediately.

 

5.

 

NEVER smoke or allow a spark or flame in vicinity of 
battery or engine.

 

6.

 

Be extra cautious to reduce risk of dropping a metal tool 
onto the battery. It could spark or short-circuit the battery 
or other electrical parts and could cause an explosion.

 

7.

 

Remove personal metal items such as rings, bracelets, 
necklaces and watches when working with a lead acid 
battery. It can produce a short circuit current high enough 

Summary of Contents for BT701

















Reviews: