![background image](http://html1.mh-extra.com/html/insteon/switchlinc-2478d/switchlinc-2478d_quick-start-manual_2069934002.webp)
INSTEON Limited Warranty – INSTEON warrants to original consumer of this product for a period of 2 years from
date of purchase, this product will be free from defects in material and workmanship and will perform in substantial
conformity with its Owner's Manual. Warranty shall not apply to defects caused by misuse or neglect.
Protected under U.S. and foreign patents (see www.insteon.com) © Copyright 2012
INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, www. Insteon.com
Using the Paddle
Paddle
Tap
Double-Tap
Press and Hold
Top
Ramp to on-level
Fast on
Brighten
Bottom
Ramp to off
Fast off
Dim
Adding SwitchLinc to a Scene as an INSTEON Responder
1) Press and hold scene controller button until it beeps
1
Controller LED will start blinking
2) Tap SwitchLinc on
Load will turn on
3) Press and hold SwitchLinc Set button until it double-beeps
Controller’s LED will stop blinking and will double-beep
2
4) Confirm scene addition was successful by tapping controller scene button on and off
The light connected to SwitchLinc will respond appropriately
Add SwitchLinc to a Scene as an INSTEON Controller
1)
Press and hold SwitchLinc’s Set button until it beeps
SwitchLinc LED will blink
2)
Adjust the scene responder(s) to the “state” you want when scene is activated from SwitchLinc (e.g., 50%, 25% or
even off)
3
3)
Press and hold responder Set button until it double-beeps (or until its LED/load flashes)
SwitchLinc will double-beep
and its LED will stop blinking
4
Responder LED will stop blinking and it may double-beep
4
4)
Confirm scene addition was successful by tapping SwitchLinc paddle on and off
Responder will toggle between the scene’s on-level and off
Owner’s Manual and Tech Support
Owner’s Manual and current Quick Start Guide:
http://www.insteon.com/support
Call: INSTEON Support Line at 800-762-7845
FCC/UL and ETL/UL Statements
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-
supplied appliance.
Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne pas installer pour commader une prise,
un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.
1
If the controller does not have a beeper, wait until its LED begins blinking
2
Most models
3
If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired scene state (on or off)
4
If either the SwitchLinc or responder’s LED continues to blink, the addition failed. Tap the device’s Set button until LED stops blinking and try again.