background image

SwitchLinc Timer Owner’s Manual  

 

Page 23 of 23 

 

SPECIFICATIONS, CERTIFICATION, AND WARRANTY 

Specifications 

View specifications for SwitchLinc Timer at: 

www.smarthome.com/2476ST.html

 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party 
testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has 
met the requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that the 
manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory 
follow-up inspections to verify continued conformance.   

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date 
of purchase, this product will be free from defects in material and workmanship and will perform in substantial 
conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or 
errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the 
product does not perform as warranted above during the warranty period, Seller will either repair it, replace it, 
or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, 
with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund 
that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or 
replacement during the warranty period, call the INSTEON Gold Support Line at 800-762-7845 with the Model 
# and Revision # of the device to receive an RMA# and send the product, along with all other required 
materials to:  

Smarthome, Inc. 
ATTN: Receiving Dept.  
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or 
implied, including any warranty or merchantability or fitness for a particular purpose. Any implied warranty, 
including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or 
supplanted as provided above shall be limited to the two-year of the express warranty above. No other 
representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the 
above warranty and disclaimer.  

Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical 
tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as 
a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from 
possession or use of this device, including without limitation damage to property and, to the extent permitted by 
law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states 
do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in 
which case the above limitations and/or exclusions may not apply to you. You may also have other legal rights 
that may vary from state to state.  

INSTEON Technology Patent 

U.S Patent No. 7,345,998, International patents pending

  

© Copyright 2011 

Smarthome, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, 

www.smarthome.com

 

 

Rev 05-31-2011 

Summary of Contents for SwitchLinc 2476ST
























Reviews: