background image

16

Certifications and Warnings

Read and understand these instructions before installing and retain them for future reference.

This product is not designed or approved for use on powerlines other than 120VAC, 50Hz or 60Hz, single 

phase. Attempting to use this product on unapproved powerlines may have hazardous consequences.

•  Use only indoors or in outdoor rated box

•  This product may feel warm during operation. The amount of heat generated is within approved limits and 

poses no hazards. To minimize heat buildup, ensure the area surrounding this product is as clear of clutter 

as possible.

•  Each Insteon product is assigned a unique Insteon I.D., which is printed on the product’s label.

•  To reduce the risk of overheating and possible damage to other equipment, do not use this product to 

control loads in excess of the specified maximum(s) or, install in locations with electricity specifications 

which are outside of the product’s specifications. If this device supports dimming, please note that dimming 

an inductive load, such as a fan or transformer, could cause damage to the dimmer, the load bearing 

device, or both. If the manufacturer of the load device does not recommend dimming, use a non-dimming 

Insteon device. USER ASSUMES ALL RISKS ASSOCIATED WITH DIMMING AN INDUCTIVE LOAD. 

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device 

must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts 

de licence. L’exploitation est autorise aux deux conditions suivantes: (1) l’appareil ne doit pas produire de 

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est 

susceptible d’en compromettre le fonctionnement.

CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control 

a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance. 

Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la 

possibilite d’endommagement a d’autres materiels, ne pas installer pour commader une prise, un appareil a 

moteur, une lampe fluorescente ou un appareil alimente par un transformateur.

Summary of Contents for 2867-222


















Reviews: