InstantEye Mk-3 GEN4-D1 Product Manual Download Page 41

Page: 41 / 68

InstantEye Mk-3 GEN4-D1 sUAS Technical Manual

Revision M1.2

August 14, 2019

ITAR or EXPORT CONTROLLED

Page 41

4. Warnings and Emergency Procedures

The InstantEye Mk-3 GEN4-D1 system was designed with a focus on safety. The system

has numerous warning messages built into the software to indicate when a potential

problem exists. These warnings help identify when emergency procedures need to be

initiated. A complete list of the system’s warning messages and descriptions of the

emergency procedures are provided below. All operators should make sure to familiarize

themselves with these procedures and periodically review them to ensure they are

prepared to rapidly respond in the event of an emergency. Many emergency situations

are remedied using the same few key emergency response actions.

4.1. Warning Messages

Provided in Table 1 is a summary of all of the potential warning messages that an operator

may encounter, along with a further description of the message and/or recommended

response to each.

Table 1. Warning messages and their recommended response.

Warning Message

Description and Recommended Response

Warning: Storage is full

Use InstantEye app to delete previously recorded

videos

Warning: Possible button; error try releasing Release button or ensure no buttons are engaged
Warning: Aircraft overheating

Land immediately / do not launch
Can cause loss of altitude control – exit ALT mode if

needed

Warning: Home mode enabled

Notifies user that aircraft is headed to home location
If user engaged HOME mode, this is just informational
If user did not engage HOME mode, this indicates lost

communications – regain control when data begins to

update

Warning: Aircraft is landing

Notifies user that the aircraft has entered landing mode

Warning: Compass heading error

Gain altitude to clear affected error
If aircraft circles or behaves erratically, disable NAV

and use video to pilot the aircraft home
If error is displayed prior to launch, do not launch and

move away from possible magnetic interference

Warning: GPS fault detected; waypoint reset GPS signal may be erratic – pilot aircraft home using

video and DO NOT engage HOME mode
Check range/bearing graphic – range may be incorrect

Warning: Aircraft lost GPS; NAV mode

disabled

Use video to pilot aircraft home
DO NOT engage HOME mode
Range/bearing graphic will not work

Summary of Contents for Mk-3 GEN4-D1





































































Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands

InstantEye Mk-3 GEN4-D1, Product Manual

Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands