background image

12 

 

If you do not set any value using the knobs, the GND BAL value will always be displayed in the lower 
right corner.  

GND  BAL  is  an  internal  setting  for  soil  composition  and  is  shown  in  the  lower  right  corner  of  the 
display. The original value is 82.9 which is the best starting point. 

After performing GROUND GRAB, the GND BAL value changes according to the soil composition. 

You can also set the GROUND BAL using the + and - buttons. See the SOIL COMPOSITION chapter 
for more information. Experienced users prefer to set GND BAL to a value where they receive only a 
weak steady signal and thus be able to better distinguish a possible item. Adjust the value above with 
the + button. 

TARGET SCALE 

The  arc  scale  at  the  top  of  the  display  classifies  metal  objects.  Each  time  an  object  is  detected,  the 
scale  indicators  light  up.  The  segments  will  be  displayed  for  3  seconds.  Identification  shows  the 
probable composition of the object. For more information, read the METAL IDENTIFICATION chapter. 
The  obejct  is  identified  by  an ID  number. If you find  an  object  in ALL METAL  mode, we recommend 
switching to DISCRIMINATION mode for more accurate identification using a two-digit ID number. 

CONTROL IN DISCRIMINATION MODE 

This mode is used to eliminate objects that are not the target of the findings, such as nails, foils, and 
other scrap metal. The coil must be in motion for detection. DISCRIMINATION mode is less sensitive 
to small objects or objects that are deeper. 

GROUND GRAB (GG)  

This  function  cannot  be  set  in  DISCRIMINATION  mode.  To  set GG,  you  must  switch  the  detector  to 
ALL METAL mode. The settings are also transferred to DISCRIMINATION mode. 

SETTINGS 

During setup, the values in the lower right corner of the screen change. 

GAIN 

If you are a beginner, start with a lower value so that you do not hear any sounds as the coil moves. 
Set the knob position to 12:00 or less. 

In this mode, GAIN sets the sensitivity. The higher the value, the deeper hidden objects can be found 
and the more the detector responds to small objects. 

MODE 

This knob is not used in this mode. Turn the knob counterclockwise as far as it will go. Turn the knob 
to change the mode from DISCRIMINATION to ALL METAL. 

DISC  

Use  the  +  and  -  buttons  to  adjust  the  DISC  value  to  eliminate  unwanted  metal  objects.  Using  the 
buttons  changes  the  value  by  1,  holding  it  increases  the  values  faster.  A  higher  value  eliminates 
unwanted metals, a lower value includes more metals. 

See the METAL IDENTIFICATION chapter for more information. 

UNWANTED SOUND NOTIFICATIONS 

This device is very sensitive, unwanted  notifications can be caused by electromagnetic  interferences 
caused by electrical devices. 

COIL MOVEMENT 

Move the coil parallel to the ground and in one level. Avoid lifting the coil while searching for objects. 

PINPOINT 

Press and hold the PINPOINT button to narrow the area of the found object. PINPOINT is a detection 
mode that does not need a moving coil. 

Summary of Contents for IN 22123






















Reviews: