background image

 

 

The ideal battery charging temper

ature is +10 ° C to +30 ° C. 

 

If you use the battery for an extended period, its temperature will be higher. This is a normal 

battery condition. 

 

If you use the battery in a cold environment, the range is lower. 

 

Do not repair or modify the battery yourself. 

USE 

 

Before use, make sure that all parts are properly assembled, tightened and not damaged. 

 

Check the brakes. 

 

Check that the folding mechanism is properly locked. 

 

Make sure the battery is properly charged. 

 

Make sure the tires are in good condition. 

 

Check the handlebar. It must be properly tightened. 

 

Get  to  know  the  surroundings,  make  sure  that  you  do  not  endanger  yourself  and  your 

surroundings. 

 

Do not drive on slippery surfaces. 

 

Wear personal protective equipment including a helmet and a sturdy shoe. 

 

Do not use if outdoor conditions are poor. 

 

Moisture reduces braking efficiency. 

RIDING TECHNIQUE 

 

Know the scooter before first use and test your ability to control this product. 

 

Turn continuously and brake safely having enough free space. 

 

Practice your first ride in an open area without obstacles. 

 

Never let distract your mind during riding. 

Foot position

 

– put your foot on the board as close to the front part as possible. Let your other foot on 

the  ground.  Make  sure  the  route  is  clean  and  free.  To  start  riding,  push  yourself  forwards  (like  on  a 
non-motorized  scooter).  Push  off  with  the  foot  that  is  on  the  ground.  Immediately  after  pressing  the 
throttle  downwards,  tilt  your  body  forwards  as  a  prevention  from  falling  back  while  increasing  your 
speed. Avoid excessive body pressing on the handlebars during speed changing. One foot is at front 
and the second one is back. It is comfortable to place the feet like on a skateboard for optimal stability. 

NOTE:

 Riding on a scooter can be dangerous. You use the product on your own responsibility and be 

familiar with all the safety precautions before riding. 

Turning

 

–  it  is  the  same  as  on  a  surf  or  snowboard.  The  handlebar  should  be  parallel  to  the  body. 

Before turning look at the approaching direction to be sure the operation is safe. 

Braking

 

–  shift  your  weight  backwards  so  that  the  braking  is  realized  through  your  feet  and  not 

through  handlebar  and  steering  system.  Learn  well  to  adjust  the  gravity  center  during  stopping  to 
avoid turning over or excessive wearing of the braking and steering system 

CLEANING AND MAINTENANCE 

The  scooter  must  be  switched  off,  disconnected  from  the  charger  and  the  charging  port  must  be 
covered before cleaning or maintenance. 

Clean the scooter with a damp cloth and a mild detergent. 

Do not use solvents or other aggressive cleaning agents. 

Summary of Contents for Billar IN 20041














Reviews: