background image

 

Document: 9700

-

03499 Rev B                                                            18                                  www.insingermachine.com 800

-

344

-

DAILY CLEANING PROCEDURES 

 

1.

 

Remove all internal removable parts including 

spray manifolds, scrap screens, drain overflow , 

suction strainers and curtains.

 

2.

 

Remove the end caps from the spray manifolds 

and clean with the brush provided. Flush the 

manifolds. 

 

3.

 

Flush scrap screens.

 

4.

 

Clean drain overflow tube.

 

PART 4   CLEANING INSTRUCTIONS

 

 

NOTE: 

 

Improper cleaning of the suction strainers will 

cause the pumps to cavitate. This will cause 

poor washing results.

 

 

5.

 

Clean the suction strainers of build

-

up.

 

6.

 

Clean the tank level cup with a plastic abrasive 

pad (do not use steel wool).

 

7.

 

Clean curtains. When the curtains are beyond 

cleaning or torn they should be replaced.

 

8.

 

Clean final rinse nozzles of matter clogging the 

jet spray.

 

9.

 

Leave the doors open to allow the drying of the 

interior surfaces.

 

The following cleaning procedures should be done daily, at the end of the shift.

 

WEEKLY CLEANING PROCEDURES

 

An DELIME switch is provided on the control panel. 

Switch has three horizontal bars and is right of 

power switch. Pressing the DELIME switch will start 

the delime cycle. The LED

s will be cyan in color. 

Consult your detergent supplier for de

-

liming solu-

tion concentration and frequency of use.

 

 

NOTE: 

 

V

-

cup seal on the drain overflow may 

 

become gummed not allowing the overflow 

 

tube to seal. This will cause the drain to leak 

water. Remove any build

-

up on the V

-

cup 

seal. When the seal becomes worn, replace 

with part # 4025

-

01541.

 

 

NOTE: 

 

Level cup must be cleaned daily. Build

-

up of 

grease and dirt will cause faulty operation of 

the tank fill heating system.

 

The LIQUID LEVEL CUP is located below the scrap 

screens in those tanks which contain water heating 

devices (coils, steam injectors, or electric immer-

sion heaters) and pump inlet strainers.  They are 

usually located, in rackless and rack conveyor style 

machines, on the inside tank wall opposite and par-

allel to the inspection doors

 

Summary of Contents for ADMIRAL 44 ADVANCED








































Reviews: