background image

Page | 4 
 

Chassis Power Connection 

Before connecting or disconnecting ground or power wires to the chassis, ensure that power is 
removed from the device. To ensure that all power is OFF, locate the circuit breaker on the 
panel board that services the device, switch the circuit breaker to the OFF position, and tape the 
switch handle of the circuit breaker in the OFF position.  

 

Work During Lightning Activity 

Do not work on the system or connect or disconnect cables during periods of lightning activity. 
 

Comply with Local and National Electrical Codes 

Installation of the equipment must comply with local and national electrical codes 
 

Do Not Exceed Input and Output Ratings 

Do not operate the product to exceed the power input and output ratings. 
 

This product Conforms to the following safety standards 

Specification 

Description 

Regulatory Compliance 

Products with the CE Marking are compliant with the 89/336/EEC 
and 73/23/EEC directives, which include the safety and EMC 
standards listed. 

Safety 

UL/CSA 60950 
UL 60601-1 
IEC 60950 with all country deviations 
EN60950 

EMC 

FCC Part 15 Class A 
CE Marking 

 

Packing List 

Each package includes the following items: 

  LPS2000 (1) 

  WM0001 Wall Mounting Kit (1) 

  AC Power Cable with one 3-PIN AC Power Connector (1) 

  User Manual (1) 

  Warranty Sheet (1) 

 

 

 

 

 

 

 

Summary of Contents for Link Power LPS2400-T1









Reviews: