11.10.20 357-06536-01 Rev A © Inovonics, 2020 - www.inovonics.com
5
Note:
Users that have achieved certification and will install UL 2560
certified systems are responsible for labeling all fundamental devices with
the UL 2560 system certification mark.
Compatible receiver for UL 2560 installations with the EN1221S-60 series
pendants: EN6080 area control gateway or EN6040-T network coordinator
with transformer.
Compatible repeater for UL 2560 installations with the EN1221S-60 series
pendants: EN5040-20T.
Note:
Inovonics supports recycling and reuse whenever possible. Please
recycle these parts using a certified electronics recycler.
Note:
Specifications and data are subject to change without notice.
12 Power Management System Information
This equipment uses a two-stage power system:
• One CR2032 lithium-metal coin cell battery which is replaceable by
installers.
• One rechargeable lithium-ion polymer pouch energy cell which is non-
accessible and non-replaceable.
12.1 Battery Handling
If you are installing CR2032 lithium metal coin cell batteries in multiple
devices, keep the batteries from coming into contact with each other to
prevent discharge.
12.2 Shipping
Both lithium-ion and lithium-metal battery types are subject to
transportation regulations such as International Air Transport Association
(IATA), International Maritime Dangerous Goods (IMDG), US Department
of Transportation (DOT) and UN Recommendation on the Transport of
Dangerous Goods.
To prevent accidental alarm activation due to air pressure changes,
Inovonics recommends that you avoid shipping the devices by air with the
CR2032 lithium-metal coin cell battery installed in the device.
When disposing of this electronic device or depleted CR2032 lithium-metal
coin cell batteries, please do so in accordance with federal, state and local
regulations.
12.3 Cold Weather Best Practices
• We recommend that the pendant be shipped without the coin cell
battery installed, especially if shipping conditions will be below 32° F
(0° C).
• If exposed to conditions below 32°F (0° C) during shipping, the
pendant should be kept at room temperature for 24 hours before
installing the coin cell battery and activating the pendant.
• If an end user is outdoors when temperatures are below 32°F (0° C)
the pendant should be worn under clothing to protect it from exposure.
• After the pendant has had the battery installed and has been
activated, the pendant should not be left in a cold vehicle below 32°F
(0° C) for any period of time.
13 Television and Radio Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
14 FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product
procedures.
15 FCC Part 15 and Industry Canada Compliance
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device. Changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Note:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
16 Medical Device Interference
Under FDA and FCC guidelines, the responsibility for verifying continuous
and safe operation of medical devices such as pacemakers and implanted
defibrillators in the presence of electromagnetic interference (EMI) rests
with the manufacturer of the medical device. As such, Inovonics does not
have the authority or specific device knowledge to conduct or interpret
formal tests on their behalf.
Inovonics transmitter devices comply with Part 15 of the FCC Rules and
Industry Canada license-exempt RSS standards.
If you have any concerns about the use of Inovonics transmitter devices in
the presence of medical devices used by a particular resident or patient, we
recommend that you consult with their physician. Another potential source
for answers is the medical device manufacturer, who can provide more
information as to their compliance with federal guidelines and how they
have addressed EMI risk.
17 Radiation Exposure Limits
This equipment complies with ISED RSS-102 radiation exposure limits set
forth for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Cet équipement est conforme avec ISED RSS-102 des limites d'exposition
aux rayonnements définies pour un environnement non contrôlé. Les
utilisateurs finaux doivent suivre le fonctionnement spécifiqueinstructions
pour satisfaire la conformité à l'exposition RF. Cet émetteur doitne pas être
colocalisé ou fonctionner conjointement avec une autre antenne ou
émetteur.