4.2.20 357-05818-01 Rev A © Inovonics, 2020 - www.inovonics.com
3
3.1 Default Transmitter Programming
3.2 Default Trouble Condition Programming
4 Access Levels
There are three levels of EE4232MR access available to users. Only the
level 2 authorized user and level 3 authorized installer are able to access
EE4232MR menus.
During normal operation there is no visual indication of system status or
activity on the LCD of the EE4232MR receiver. Unless the level 2
authorized user or the level 3 authorized installer enters a valid password,
the LCD will remain completely blank.
To enter either the level 2 authorized user or the level 3 authorized installer
password:
1.
Press any button; P
ASSWORD
displays.
• Once P
ASSWORD
displays, the password must be entered within 60
seconds; if it is not entered within 60 seconds, the attempt will be
counted as an incorrect password.
2.
Use the
Up
and
Down
buttons to scroll through the numerals; press
Enter
to select.
• The
Back
button deletes the last character entered.
3.
Repeat step 2 for each numeral in the password.
4.
When all numerals in the password have been entered, press
Enter
.
Note:
If an incorrect password is entered, all EE4232MR buttons will lock
up for 90 seconds. If five incorrect passwords in a row are entered, the
receiver will send a tamper fault and log the event. The tamper fault will be
cleared once the correct password is entered.
5 Level 2 Access
Note:
The default level 2 authorized user password is 1234.
Level 2 authorized users have access to two menu options after entering
their password: S
YSTEM
T
EST
and S
YSTEM
S
TATUS
.
5.1 System Test
System test mode is used to perform a functional test of all of the
transmitters programmed into the system. Upon entry into test mode, the
receiver outputs will be cleared, and transmissions will not generate the
defined outputs. System test mode will timeout after 30 minutes of
inactivity.
Note:
System test mode only tests transmitters; repeaters are not tested.
To perform a system test:
1.
Select S
YSTEM
T
EST
to enter system test mode.
2.
Activate each of the transmitters in the system.
Note:
An activation from any condition of a multiple condition transmitter
will satisfy the test requirement for the entire transmitter. For example,
pressing any button on an EE1236D three-condition pendant will satisfy the
test requirement for the entire transmitter.
3.
Use the
Up
and
Down
buttons to scroll through the transmitters.
• Transmitters which have not sent an activation signal will display only
the point number.
• Transmitters which have sent an activation signal will display the point
number followed by ****.
Transmitter Alarms
Output
1, 11, 21, 31
1
2, 12, 22, 32
2
3, 13, 23
3
4, 14, 24
4
5, 15, 25
5
6, 16, 26
6
7, 17, 27
7
8, 18, 28
8
9, 19, 29
9
10, 20, 30
10
Condition
Output
Tamper
11
Low Battery
12
Supervision Loss/Inactive
12
Line Power Loss
12
Access level
Access
Level 1
No menu access
Level 2
Can view system status indicators and enter
system test mode as included in the following
menus:
• S
YSTEM
S
TATUS
• S
YSTEM
T
EST
Level 3
Can view system status indicators, change
receiver system parameters, and perform the
receiver functions included in the following
menus:
• P
OINT
S
TATUS
• I
NSTALL
& S
ERVICE
• S
ETUP
P
OINT
• PW P
ROT
LED
S
• S
YSTEM
T
EST
• F
ACTORY
C
ONFIG
• S
ELECT
L
ANGUAGE
• C
HANGE
P
ASSWORD
• S
IGNAL
S
TRENGTH
• D
ELETE
P
OINT
• R
EGISTER
X
MITTER
• E
VENT
L
OG
• Event Log
Access level
Access
