inout DA 480-R User Manual Download Page 2

DA 480-R User manual  v.1

Page 1

Warranty

DA 480-R is covered by 24 month warranty on its electronics parts, starting from the date of
purchase. This warranty becomes void in case of tampering with the device and in case of
work carried out on it by people that were not authorized by the manufacturer or by an
authorized dealer. Warranty conditions are those described in the “Warranty Rules”.

NOTE - responsibility of the purchaser: in case of repair under warranty, the device must be
packed in order to avoid damage during transport and shipped to the manufacturer together
with all the accessories.

Warranty Rules.

1.  In order to exercise his warranty rights, the purchaser must include with the device a copy

of the evidence of purchase duly stamped by the dealer (bill/invoice).

2.  The warranty lasts 24 months on the electronic parts. The warranty is granted at the point

of sale or it could be directly requested to the manufacturer.

3.  The warranty only covers damage to the product which makes it work badly.

4.  Work under warranty will only mean repairing or replacing, free of charge, any parts

acknowledged being defective during manufacture or in their material, including labour
costs.

5.  The warranty does not apply to damage caused by negligence or failure to comply with the

instructions, or damage caused by unauthorised people, with a special reference to the
external parts.

6.  Also, the warranty does not apply to damage caused to the device by connection to

unsuitable power sources.

7.  The warranty does not cover parts that are subject to wear as a consequence of the use,

as well as the chassis if the material is not defective.

8. The warranty does not include transport costs, which will be paid by the purchaser

depending on way and time of transport.

9.  The warranty expires 24 months after the purchase. In this case, service will be provided

charging for the replaced parts, labour costs and transport according to the current rates.

10. In case of any controversy the Court of Law of Venice has the exclusive jurisdiction.

Summary of Contents for DA 480-R






























Reviews: