background image

SAFETY AND WARNINGS BEFORE YOU BEGIN

 

WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD 
RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE           
IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS.

 

NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.

 

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REASON AS GIVEN 
ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WARRANTY.

 

HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND IS FUNCTIONING PROPERLY.

 

THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE OF THE GAME. IF THE 
A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, 
WHICH COULD CAUSE DAMAGE.

 

THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES OTHER THAN THOSE IT WAS 
DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT FOR VOLTAGE CONVERSION INFORMATION.

 

WARNING

 

DO NOT remove any of the components on the main board (e.g. compact flash and EPROMS) while the game 
is powered on. This may cause permanent damage to the parts and the main board. Removing any main 
board component part while powered on will void the warranty.

 

ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE,

 

UNLESS NEEDED FOR SPECIFIC TESTING.  FAILURE TO OBSERVE THIS PRECAUTION

 

COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.

 

THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE USED.

 

This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical,  sensory  or  mental           
capabilities, or lack of experience and knowledge, unless  they have  been given supervision or instruction concerning 
use of the appliance by a person responsible for their safety.

 

 Children should be supervised to ensure that they do not 

play with the appliance.

 

 

AC Power Information

 

The games main fuse is accessed at the back of the game and at the power 
mod.  Above the power cord is a small panel that contains the main fuse.  The 
value of the fuse for 120 volt users is 7 AMPS at 250Volt type slow blow.  The 
value of the fuse for 230 users is 3.5 AMPS at 250Volt type slow blow. 

 

Summary of Contents for WaterFuls WR1000EX


















Reviews: