Innova FLOAT FN04M5W Owner'S Manual Download Page 4

 

 

 

 

 

PRODUCT RATINGS: 

The product’s lift motors are not designed for continuous use of more than 2 minutes in 
an 18 minute period, or approximately 10% duty cycle. For every 30 minutes of use for 
the massage motor, 30 minutes of rest is needed. The massage functions should be 
used for a total of 2 hrs in a 12 hr period.  Any attempt to circumvent or exceed this 
rating will shorten the life expectancy of the product and may void the warranty. 
 

WEIGHT LIMITS: 

The limitation for this product is 750 lbs. This product will structurally support up to 750 
lbs, provided the mattress is evenly distributed across the product and the weight isn’t 
concentrated in one area. This product is not designed to support or lift such amounts in 
the head or foot section alone. Exceeding this weight restriction will void the warranty and 
could damage the bed and/or cause injury. Enter and exit the bed in a flat position and 
do not sit on the head or foot sections while this product is in the raised position. 
 

ELECTRONIC MECHANISMS: 

It is normal for the raising and lowering feature of this product to emit a minimal humming 
sound during operation.  The massage feature creates a vibrating hum during operation 
and the resonance will increase accordingly with a higher intensity motor setting.  
 

LOCATION ENVIRONMENT: 

The level of sound experienced in a room is directly related to the environment within that 
location.  In a room with hardwood floors and the massager turned on, a vibrating noise 
may be noticeable. Placing a piece of carpet or rubber casters cups under the legs of the 
product may reduce this resonance. The rubber caster cups also prevent the product from 
sliding when located on smooth or hard surface flooring. 
 

TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY: 

Make sure the product is in the flat position before unplugging from power source. Always 
unplug the product from the electrical outlet before cleaning or servicing the product. If 
the  cord  or  plug  is  damaged,  document  the  damage  and  contact  customer  service  for 
advisement on continued use.

 

 

MANUAL VERSION: 080403

 

Summary of Contents for FLOAT FN04M5W





















Reviews: