Talaria TWO
TM
Evaluation & Development Kit
Version 2.0
1
©InnoPhase, Inc. 2021
Contents
Figures ...................................................................................................................................... 3
2
Tables ....................................................................................................................................... 3
3
Terms & Definitions ................................................................................................................. 4
4
Introduction ............................................................................................................................. 5
5
INP301x Package Contents ..................................................................................................... 5
6
Description of the board .......................................................................................................... 6
6.1
Block Diagram .................................................................................................................... 6
6.2
Jumpers on the board ........................................................................................................ 8
6.3
Power Supply and Mode Switch ........................................................................................ 9
6.4
IO Header (J1) .................................................................................................................. 10
6.5
Shield Headers (JP1 to JP4) .............................................................................................. 11
6.6
On Board Sensors ............................................................................................................ 12
7
Functional Description ........................................................................................................... 13
7.1
Stand-alone mode ........................................................................................................... 13
7.1.1
Driver Installation for Windows OS .......................................................................... 14
7.2
Shield Mode ..................................................................................................................... 19
7.2.1
EVB-A as Wi-Fi Shield with STM32 Nucleo Board .................................................... 19
8
Power Measurement ............................................................................................................. 20
9
Using Battery as Power Source .............................................................................................. 21
10
FCC/ISED Regulatory Notices .............................................................................................. 22
10.1
Modification Statement ................................................................................................... 22
10.2
Interference Statement ................................................................................................... 22
10.3
Radio Frequency Radiation Exposure Statement ............................................................ 22
10.4
RF Exposure Statement for Module Integration ............................................................. 23
10.5
Labeling Requirements for the Host Device .................................................................... 24
10.5.1
INP1010 .................................................................................................................... 25
10.5.2
INP1011 .................................................................................................................... 25
10.5.3
INP1012 .................................................................................................................... 26
10.5.4
INP1013 .................................................................................................................... 26
11
Support ................................................................................................................................ 27
