Inmes IM-3 SE, Operation Manual

Page: 7 / 12

INMES Industrial Ltda –IM-3 SE
7
TROUBLESHOOTING
Drive rod stuck - This can happen if:
a) Residues /dirt have gotten into the driver head assembly causing the drive rod to stick after it pushed up the wedge,
not returning to its original position.
b) The wedges were placed in the cartridge upside down, i.e. with the glue side down. The glue side of the wedges is the
cutting edge, and must face up. If the wedges are placed glue side down, instead of the drive rod pushing against the
base of the wedge, the bevel on the cutting edge will act as a guide that directs the drive rod along the side of the
wedge, causing the rod to get stuck, since it and the wedge are occupying the space designed for the drive rod alone.
To release the drive rod, simply pull down on the air cylinder. This will pull back the drive rod to its original position. Then
make sure that the wedges have the glue side facing up in the cartridge. If they are in the proper position, you should
clean the drive head assembly. If you cannot pull the air cylinder down, you should then perform the procedure described
in paragraph 3 in the Maintenance section of this manual.
PARTS LIST FOR IM-3 SE
CODE DESCRIPTION CODE DESCRIPTION
0301003 Base for positioning stops 0408046
Bolt M10X90mm
0301005 Bushing 0408069
Nut M10
0301011 Guide bar for wedge spring loader 0408113 Bolt M4x12mm
0301013 Nut M16 0408140 Bolt Hex. M8x25mm
0301014 Chain’s protector 0408144 Steel Rivet 3,2x10,2mm
0301015 Chain’s guide 0408160 Nut M4
0301022 Down support arm 0416012 Spring
0301029 Spring-loaded cable shoe plate 0417008 Flex pin
0301031 Magazine for 7mm wedges 0417009 Flex pin
0301032 Magazine for 10mm wedges 0417010 Flex pin
0301033 Magazine for 15mm wedges 0417011 Flex pin
0301038 Bolt M5 0417012 Bushing
0301042 Pressure pad assembly shaft 0417088 Flex pin 5x14mm
0301054 Main Shaft washer 0504015 Label
0301060 Anti-Sliding sticker
0408007
Bolt M4X10mm
0301079 Magazine for 12mm wedges
0408155 Allen wrench 3mm
0301080 Base leg
0408139 Allen wrench 4.0mm
0301081 Moulding guide and Teflon pad
0408075 Allen wrench 5.0mm
0301087 Guide for drive piston
0408076 Allen wrench 6.0mm
0301201 Aluminum table top
0408205 Allen wrench 8.0mm
0301207
Main shaft IM-2/IM-3/3P
0408258
Wrench 17x19mm
0301212
Chain IM-2/IM-3
P0301051
Spring loaded cable IM-2
0301397
FootPedal IM-2/IM-3
P0301164
Bushing IM-2/ IM-3/3P
0301398
Foot pedal support IM-2/IM3
P0301028
Position Stop IM-2
0301600
Bracket
P0301030 Wedge shoe
0301601
Pin Button
P0301200
Drive head assemblyIM-2/IM-3/3P
0301602
Screw M8
P0408016 Bolt M6X16mm
0301604 Upper Support IM-2/IM-3/IM-3P (Z)
P0301199
Drive rod IM-2
0403003 Plastic foot
P0301005
Bushing IM-2
0405120 Label
P0301208
Bushing IM-2/IM-3/3P
0408005 Bolt M3x16mm P0301606 Button (Z)
0408009 Bolt M4x20mm
P0301632
V01 Pressure Pad
0408012 Bolt M5x8mm
P0301633
V02 Pressure Pad
0408018 Bolt M6x20mm
P0301634
V03 Pressure Pad
0408025 Bolt M8X16mm P0301635 Round Pressure Pad D50mm
0408029 Bolt M8x35mm P0301636 Round Pressure Pad D25mm
0408037
Bolt M10X25mm
P0416002 Spring IM-2