background image

 

 

 

ITC-308 User Manual

 

Inkbird Tech. Co., Ltd.                                                                        www.ink-bird.com

 

 

When  measured  temperature  is  lower  or  equal  to  AL,  low  temperature  alarm  will  be 

triggered, buzzer will alarm with tone “bi-bi-Biii” until the temperature >AL or any key is 
pressed.  

 

5.3 Compressor Delay (PT) 

Under refrigeration mode, after power on, if the measured temperature is higher than the 

value  of  setting  temperature(TS)  plus  cooling  differential(CD),  the  equipment  won’t  start 

refrigeration immediately, but waiting for a delay time.  

When the time interval between two refrigeration operation is larger than preset delay, the 
equipment  will  start  refrigeration  immediately;  when  the  time  interval  between  two 

refrigeration is less than preset delay, the equipment won’t start refrigeration until preset 

delay is satisfied.  
Delay time will be calculated right after the moment refrigeration stops.  

 

5.4 Temperature Calibration (CA) 

When  there  is  deviation  between  measured  temperature  and  actual  temperature,  use 

temperature  calibration  function  to  align  the  measured  temperature  and  actual 

temperature.  The  corrected  temperature  is  equal  to  temperature  before  calibration  plus 
corrected value(corrected value could be positive value, 0 or negative value

.   

 

5.5 Display in Fahrenheit or Centigrade unit (CF) 

Users  can  select  display  with  Fahrenheit  or  Centigrade  temperature  value  according  to 
their  own  habit.  Default  setting  is  display  with  Centigrade  temperature  value.  For 

displaying with Fahrenheit temperature value, set CF value as F.  

Attentions:  when  CF  value  changed,  all  the  setting  value  will  be  recovered  to  factory 
settings.  

 

 

 

 

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for ITC-308












Reviews: