manualshive.com logo in svg

Initio INI-9100U, User Manual

Share
Download
Initio INI-9100U User Manual Download Page 73

8-3

Installation

The drivers developed by Initio for NetWare will be installed on the disk drive
used for NetWare system initialization.  It is strongly recommended that the
selected procedure be read and understood before continuing with the system
configuration or change. Please read the instructions carefully.

New NetWare 4.xx installation

Drivers for the Initio host adapter may be found on the INITIO INI-
9100U/9100UW DRIVER DISK 1.  In most cases you will load the drivers
during a new installation of NetWare from CD-ROM.  The driver is loaded
during  the NetWare Server Installation procedure. The NetWare installation
program will prompt you for the required parameters as the installation
procedure progresses.  It is highly recommended that you have a copy of the
Novell Netware Installation and Upgrade Manual for reference.

1. At the MS-DOS prompt for CD-ROM installation, change directories

to where the installation files are located.

 

e.g., d:\netware4.0\english\  <ENTER>

2. Type INSTALL <ENTER> to initialize the installation routine.   A

screen similar to the following will be displayed (see figure 8-1).

Summary of Contents for INI-9100U





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands