manualshive.com logo in svg

Ingersoll-Rand QE8 Series, Service Manual, Page: 18 / 28

Share
Download
Ingersoll-Rand QE8 Series Service Manual Download Page 18

18

MAINTENANCE 

(Continued)

Disassembly of External Components

1. Dislodge O-rings (15) and remove Memory Chip (7) 

from assembly.

2. Remove Trigger mechanism (5) from Motor Housing 

Assembly.

3. Remove Spring (6) from Trigger mechanism.
4. Slide Reverse Ring (17) away from Motor Housing 

Assembly, being careful not to lose the Detent Ball (3) 
or Springs (4) and (16).

5. Remove Retaining Ring (14) from behind Label Cover 

Lens (13).

6. In a sliding motion, pull Warning Label (12) and Label 

Cover Lens (13) off end of Motor Housing Assembly. 

7. Slide Housing Cover (11) off Motor Housing 

Assembly.

8. Remove O-ring (10) located at front of Housing Cover.

Communication Board

(Dwg. TP2162a)

(Dwg. TP2162b)

Disassembly of Internal Components

1. Remove Retainer (9) used to retain Communication 

Board (8), located at rear end of Motor Housing 
Assembly in Connector cavity. 

2. In large cavity area(s) of Motor Housing, disconnect 

the Motor Phase connector. 

(Refer to TP2162b)

 

3. Disconnect the Motor temperature-sensor connector 

from the Communication Board. 

(Refer to TP2162b)

 

4. Disconnect the Motor Commutation connector from 

the Communication Board. 

(Refer to TP2162a).

Torque and Motor Connector(s)

Torqu

e Transduc

er

Motor

Commuta

tion

LEDs and Temperature Connector(s)

Motor Temperature

Se

ns

or

LED

Bo

ar

d

Summary of Contents for QE8 Series





























Reviews:

No comments