Manual 22077473
35
11/30/06
FLUIDS AND LUBRICATION TABLE
Ingersoll-Rand
Preferred Fluids
1 gal. (3.8 litre)
5 gal. (19.0 litre)
55 gal. (208.2 litre)
220 gal. (835 litre)
IR Pro-Tec
™
36899698 36899706 36899714 36899722
IR XHP605
-
22252076
22252050
22252068
IR XHP1001
-
35612738
35300516
-
XHP405
-
22252126
22252100
22252118
Engine Oil
54480918
36875938
36866903
If the unit has been operated for 1,000 hours, it should be
completely drained of oil. If the unit has been operated under
adverse conditions or under long shutdown periods, an earlier
change may be necessary as oil deteriorates with time as well
as by operating conditions. Complete replacement of the old oil
with clean oil every 500 to 1,000 hours, depending upon
operating conditions, not only is desirable, but is good insurance
against the accumulation of dirt, sludge or oxidized oil products.
Completely drain the receiver/separator and the piping. If the oil
is drained immediately after the
unit has been run for some time,
most of the sediment will be in suspension and will drain more
readily.
Note:
Shorter oil change intervals may be necessary if unit is
operated under adverse conditions.
Do not, under any circumstances, open any drain cocks, remove
any plugs or the oil filler plug from
the
compressor
lubricating
and cooling oil system without making sure the air receiver
system had been completely relieved of all air pressure.
Some oil mixtures are incompatible with each other and result in
the formation of varnishes, shellacs or lacquers, which may be
insoluble. Such deposits can cause serious trouble including
clogging of the filter. Where possible, try to avoid mixing oils of
the same type but different brands. A brand change is best
made at the time of a complete oil change. Refer to the
Fluids
& Lubrication Table
for oil recommendation.
CAUTION
WARNING
Refer to these charts for correct compressor fluid required.
Note that the selection of fluid is dependent on the design
operating pressure of the machine and the ambient
temperature expected to be encountered before the next
oil change.
Note:
Fluids listed as “preferred” are required for
extended warranty.
Compressor oil carryover (oil consumption) may be
greater with the use of alternative fluids.
Design Operating
Pressure
Ambient
Temperature
Specification
100 psi to 300 psi
350 psi
-10
°
F to 125
°
F
(-23
°
C to 52
°
C)
-23
°
C to 52
°
C
(-10
°
F to 125
°
F)
65
°
F to 125
°
F
(18
°
C to 52
°
C)
Preferred:
IR Pro-Tec
™
Alternate: ISO Viscosity
Grade 46 with rust and
oxidation inhibitors,
designed for air
compressor service.
Preferred:
IR XHP605
Alternate: IR XHP405
ISO Viscosity Grade 68
Group 3 or 5 with rust
and oxidation inhibitors,
designed for air
compressor service.
Preferred:
IR XHP605
IR XHP1001
Preferred Ingersoll-Rand Fluids –
Use
of these fluids with original I-R filters can
extend warranty. Refer to operator’s
manual warranty section for details or
contact your I-R representative.
Summary of Contents for Doosan XHP1070CMH-1800
