background image

IMPORTANT SAFETY INFORMATION ENCLOSED.

READ THIS MANUAL BEFORE OPERATING PUMP.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference. 

Failure to observe the following warnings could result in injury.

INSTRUCTION MANUAL 

S237-SA

RELEASED: 

5-31-19

(REV: A)

INSTRUCTIONS FOR MODELS 

S237-SA SUMP PUMPS

NOTICE

  S237-SA is designed for construction and maintenance applications where 

light weight, compactness, and low air consumption are prime factors. Ingersoll-Rand is not 

responsible for customer modification of pumps for applications on which Ingersoll-Rand 

was not consulted.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

 (800) 495-0276 

 FAX (800) 892-6276 

© 2019 

arozone.com

PLACING PUMPS IN SERVICE

 

y

Always operate, inspect and maintain this pump in ac-

cordance with all regulations (local, state, federal and 

country), that may apply to hand held/hand operated 

pneumatic pumps.

 

y

For safety, top performance, and maximum durability of 

parts, operate this pump at 90 psig (6.2 bar/620 kPa) max-

imum air pressure at the inlet with 3/4” (19 mm) inside 

diameter air supply hose.

 

y

Always turn off the air supply and disconnect the air 

supply hose before installing, removing or adjusting any 

accessory on this pump, or before performing any main-

tenance on this pump.

 

y

Do not use damaged, frayed or deteriorated air hoses and 

fittings. 

 

y

Be sure all hoses and fittings are the correct size and are 

tightly secured. 

 

y

Always use clean, dry air at 90 psig maximum air pressure. 

Dust, corrosive fumes and/or excessive moisture can ruin 

the motor of an air pump.

 

y

Do not lubricate pumps with flammable or volatile liquids 

such as kerosene, diesel or jet fuel.

 

y

Do not remove any labels. Replace any damaged label.

 

y

This pump is not designed for working in explosive atmo-

spheres.

 

y

This pump is not insulated against electric shock.

USING THE PUMP

 

y

Always wear eye protection when operating or perform-

ing maintenance on this pump.

 

y

Always wear hearing protection when operating this 

pump.

 

y

Use accessories recommended by 

Ingersoll-Rand.

 

y

Do not start or operate this pump unless it is submerged.

NOTICE

 The use of other than genuine Inger-

soll-Rand replacement parts may result in safety haz-

ards, decreased pump performance, and increased 

maintenance, and may invalidate all warranties.

Repairs should be made only by authorized trained 

personnel. Consult your nearest Ingersoll-Rand Au-

thorized service center.

Summary of Contents for ARO S237-SA









Reviews: