manualshive.com logo in svg

Ingersoll-Rand 6WRSL3, Manual

Share
Download
Ingersoll-Rand 6WRSL3 Manual Download Page 3

3

ADJUSTMENTS

 SHUTOFF VALVE ADJUSTMENT 

 PROCEDURE

Adjustment of Shutoff Valve (for 6WT or 6WRT)

Adjustment to the Shutoff Valve system is preset at the
factory.  Do not adjust any part of the Valve unless, after
prolonged use of the Tool, the Tool shuts off prematurely
or the Tool fails to shut off.  Only if either of these
conditions exists are you to adjust the Valve.  Adjust the
Valve according to the procedures below.

1. Turn the Regulator Adjustment Screw until the top of the

Screw is approximately two threads below the face of the
Regulator Body.  Set the Bleed Adjustment Screw
approximately four threads below the face of the
Regulator Body.  See Dwg. TPD1071.

Setup of the Regulator and Bleed

Adjustment Screws

2 THREADS

3/32” HEX. WRENCH

4 THREADS

REGULATOR
ADJUSTMENT
SCREWS

(Dwg. TPD1071)

2. Cycle the tool on a test joint to test for shutoff. 

See Dwg. TPD1074.

(Dwg. TPD1074)

Test Joint – 55 psig

3. If the tool fails to shut off:

a. Turn the Bleed Adjustment Screw clockwise a 

little at a time, until consistent shutoff occurs.  If 
no shutoff occurs, reset the Bleed Adjustment 
Screw four turns under flush.  See Dwg. TPD1072.  
Set the Regulator Adjustment Screw 1/4 turn deeper 
and repeat steps 2 and 3.  See Dwg. TPD1073.

b. If tool shutoff occurs, turn the Bleed Adjustment 

Screw  counterclockwise until the tool stalls on a 
test joint.  When the tool stalls, rotate the Bleed 
Adjustment Screw clockwise, a little at a time, 
until consistent shutoff occurs.  See Dwg. TPD1072.

Setting the Regulator Adjustment Screw

5/64” HEX. WRENCH

BLEED
ADJUSTMENT
SCREW

(Dwg. TPD1072)

4.

Cycle the tool on a test joint to test for shutoff.
See Dwg. TPD1075.

Test Joint – 90 psig

(Dwg. TPD1075)

5. If the tool fails to shut off:

a. Turn the Regulator Adjustment Screw clockwise, 

a little at a time, until consistent shutoff occurs.
See Dwg. TPD1073.

b. If tool shutoff occurs, turn the Regulator 

Adjustment Screw  counterclockwise until the tool 
stalls on a test joint.  When the tool stalls, rotate 
the Regulator Adjustment Screw clockwise 1/8 of 
turn at a time until consistent shutoff occurs.  This 
adjustment provides maximum torque output at 
shutoff.

Summary of Contents for 6WRSL3




































Reviews:

No comments

Brands by name

Popular brands

Load more brands