manualshive.com logo in svg

Ingersoll-Rand 070008, Maintenance Manual

Share
Download
Ingersoll-Rand 070008 Maintenance Manual Download Page 141

Refrigeration Service Operations

140

IMPORTANT: This unit uses micro-channel 
condenser coils. Micro-channel coils are 
make of aluminum but have copper stub 
tubes at the inlet and outlet connections. 
Make sure to use a heat sink on the copper 
stub tubes to prevent damage to the heat 
shrink tubing and brazed connections (and 
the aluminum) that attached the copper stub 
tubes to the aluminum micro-channel coil. 
The heat shrink tubing is used to prevent 
corrosion between the copper and aluminum.

4. Pressurize the refrigeration system and test for 

leaks. If no leaks are found, evacuate the 
system.

5. Close the curbside condenser grille and top 

door.

6. Recharge the unit with proper refrigerant and 

check the compressor oil. 

Roadside Condenser Coil

Removal

1. Recover the refrigerant charge.

2. Open the top door and roadside condenser 

grille.

3. Unsolder the inlet and outlet refrigeration line 

connections from the copper stub tubes on the 
micro-channel condenser coil. Make sure to 
use a heat sink on the copper stub tubes.

IMPORTANT: This unit uses micro-channel 
condenser coils. Micro-channel coils are 
make of aluminum but have copper stub 
tubes at the inlet and outlet connections. 
Make sure to use a heat sink on the copper 
stub tubes to prevent damage to the heat 
shrink tubing and brazed connections (and 
the aluminum) that attached the copper stub 
tubes to the aluminum micro-channel coil. 
The heat shrink tubing is used to prevent 
corrosion between the copper and aluminum.

4. Remove the condenser coil mounting bolts 

and lift the coil from the unit.

Installation

1. Clean the fittings for soldering.

2. Place the coil in the unit and install the 

mounting bolts. 

3. Solder the inlet and outlet refrigeration line 

connections to the copper stub tubes on the 
micro-channel condenser coil. Make sure to 
use a heat sink on the copper stub tubes. 

IMPORTANT: This unit uses micro-channel 
condenser coils. Micro-channel coils are 
make of aluminum but have copper stub 
tubes at the inlet and outlet connections. 
Make sure to use a heat sink on the copper 
stub tubes to prevent damage to the heat 
shrink tubing and brazed connections (and 
the aluminum) that attached the copper stub 
tubes to the aluminum micro-channel coil. 
The heat shrink tubing is used to prevent 
corrosion between the copper and aluminum.

4. Pressurize the refrigeration system and test for 

leaks. If no leaks are found, evacuate the 
system.

5. Close the roadside condenser grille and top 

door. 

6. Recharge the unit with proper refrigerant and 

check the compressor oil. 

Radiator Coil

NOTE: The roadside condenser coil must be 
removed to remove the radiator coil. 

Removal

1. Recover the refrigerant charge.

2. Open the top door and roadside condenser 

grille.

3. Drain engine coolant from the unit. 

4. Drain engine coolant from the expansion tank. 

5. Remove the roadside condenser coil. See 

“Roadside Condenser Coil” on page 140 for 
the removal procedure.

6. Disconnect the coolant hoses from the radiator 

coil.

7. Remove the radiator coil mounting bolts and 

lift the radiator coil from the unit.

Summary of Contents for 070008




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands