Ingenico iCT2XX Operating Manual Download Page 105

Page: 105 / 147

SKYZER TECHNOLOGIES

PAGE 105 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

13.0

CHQ-PIN $10.00
****

The cardholder keys in their PIN number followed by

ENTER

14.0

PROCESSING NOW

PROCESSING NOW

will be displayed on the terminal and pinpad.

15.0

ACCEPTED

Transaction has been

ACCEPTED

and prints off transaction receipt.

16.0

DECLINED

Transaction has been

DECLINED

and prints off transaction receipt.

11.11 Credit Card Hospitality Transaction

This function allows the merchant to perform hospitality transactions.

11.11.1

Hospitality Card Status Check

This transaction requests a check that the card is valid. It is not a preauthorisation and
does not guarantee any available funds and does not store in the terminal.
The card status check may be used on any card type and is performed online.

Summary of Contents for iCT2XX




















































































































































Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands

Ingenico iCT2XX, Operating Manual

Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands