Infors HT Multitron Pro Operating Manual Download Page 132 | Manualshive

Page: 132 / 188

background image

Multitron Pro - Incubation Shaker

Operation

Page

132

of

185

2013-02-19

Display show ON and changes to the current value of the
parameter, e.g. 65%.

NOTICE!

A setpoint of 70% rH is sufficient to prevent
evaporation.
Under ideal conditions, a setpoint of 85% rH can be
used.

NOTICE!

Formation of condensation indicates that the
maximum humidity has been reached. The setpoint
value must be reduced.

7.18 Operating the cooling system

Top-mounted cooling system 900 watts / 1200 watts

The cooling system has its own power supply. The cooling system
is switched on with the green push-button on the left-hand side of
the cooling module. The push-button lights up when the cooling
system is switched on.

Side-mounted cooling system 380 watts

The incubation shaker supplies power to this cooling system. The
cooling system is ready for operation when the incubation shaker is
switched on.

External cooling system

The external cooling system is supplied via a pressurised line from
the in-house cooling system. The external cooling system is ready
for operation when the incubation shaker is switched on.

«
...
130
131
132
133
134
...
»

Summary of Contents for Multitron Pro





























































































































































































Reviews:

No comments

Related manuals for Multitron Pro

Brand: GE Pages: 698

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Haigh Pages: 60

Brand: Madsen Pages: 206

Brand: Raytec Pages: 60

Brand: Daikin Pages: 12

Brand: Napoleon Pages: 3

Brand: Daikin Pages: 52

Brand: mychway Pages: 56

Brand: Goobay Pages: 6

Brand: SAC Pages: 2

Brand: popular Pages: 27

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

Brand: xsto Pages: 63

Brand: Maselec Pages: 6

Brand: American DJ Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands