manualshive.com logo in svg

INFODRAW PMRS-420, User Manual

Share
Download
INFODRAW PMRS-420 User Manual Download Page 72

15 June, 2017                                

INFODRAW R&D 

         PMRS-420 (v2.0) User Manual v6.2.0.0 

 

 

 

 

68 

 

 

5 

 

4-1-6-2  Audio Streaming: 

 
 

 

Audio In: 
Double clicking on the “Audio In 1” channel 
opens the audio stream of just the Microphone 
on the PMRS device to the speakers on the PC. 
Double clicking again on the “Audio In 1” 
channel stops the audio stream. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Audio Out: 

 

Double clicking on the “Audio Out 1” channel 
opens the audio stream of the speakers on the 
PMRS device to the mic transmission on the PC. 
Double clicking on the “Audio In 1” channel stops 
the audio stream. 

 

Ensure that either: 

 

 
 
 
 
 
 
 

Stop Audio Stream 

 

Start Audio Stream 

a)  Headphones with a microphone are attached 

directly into the “Audio in/out TRRS Female 
Connector” on the top of the PMRS device. 

 

b)  Speakers and a Microphone are attached 

separately to the Audio in/out Splitter Cable, 
which is then connected to the PMRS unit. 

Ensure that you have speakers and a microphone 
connected to your PC. 

 

 

Summary of Contents for PMRS-420
































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands