background image

Page 31

INF8022 Series Hardware Guide

LIMITED WARRANTY

InFocus Limited Warranty For InFocus Branded Hardware Products Only

LIMITED WARRANTY.

 InFocus’s warranty obligations for the hardware products are limited to the terms set forth 

herein. InFocus warrants the InFocus-branded hardware products against defects in materials and workmanship under 
normal use for a period outlined in the Limited Warranty Periods section below from the date of retail purchase by the 
original end-user purchaser (“Warranty Period”).  The Warranty Period starts on the date of purchase. Your dated sales 
or delivery receipt, showing the date of purchase of the product, is your proof of the purchase date. You may be required 
to provide proof of purchase and proof that the product was purchased new as a condition of receiving warranty 
service. If a hardware defect arises and a valid claim is received within the Warranty Period, at its option and to the 
extent permitted by law, InFocus will either (1) repair the hardware defect at no charge, using new parts or refurbished 
parts that are equivalent to new in performance and reliability, (2) exchange the product with a product that is new or 
refurbished that is equivalent to new in performance and reliability and is at least functionally equivalent to the original 
product, or (3) refund the purchase price of the product. InFocus may request that you replace defective parts with 
customer-installable new or refurbished parts that InFocus provides in fulfillment of its warranty obligation (“Customer 
Self Repair”). A replacement product or part, including a Customer Self Repair part that has been installed in accordance 
with instructions provided by InFocus, assumes the remaining warranty of the original product or ninety (90) days from 
the date of replacement or repair, whichever provides longer coverage. When a product or part is exchanged, any 
replacement item becomes your property and the replaced item becomes InFocus’s property. Parts provided by InFocus 
in fulfillment of its warranty obligation must be used in products for which warranty service is claimed. When a refund is 
given, the product for which the refund is provided must be returned to InFocus and becomes InFocus’s property. This is 
your exclusive remedy for defective products. 

Limited Warranty Periods vary depending on your product model and the country of purchase. To review the warranty 
period associated with your product model, please refer to the product specifications information on www.infocus.
com. By inputting your product model in the Quick Search box on the website, you will find warranty terms in the 
Specifications matrix.

EXCLUSIONS AND LIMITATIONS. 

This Limited Warranty applies only to the hardware products manufactured by or 

for InFocus, and sold by InFocus, its worldwide subsidiaries, authorized resellers or country distributors, that can be 
identified by the “InFocus” trademark, trade name, or logo affixed to it, and to required firmware. The Limited Warranty 
does not apply to any non-InFocus hardware products or peripherals external to the InFocus-branded hardware 
products (including but not limited to external storage subsystems, displays, printers, speakers or other peripherals), or 
to any software applications or programs, even if packaged or sold with the InFocus hardware. Manufacturers, suppliers, 
or publishers of products, software or peripherals, other than InFocus, may provide their own warranties to the end 
user purchaser, but InFocus, in so far as permitted by law, provides their products “AS IS” without the InFocus Limited 
Warranty. Software distributed by InFocus with or without the InFocus brand name (including, but not limited to system 
software) is not covered under this Limited Warranty. Refer to the licensing agreement accompanying the software for 
details of your rights with respect to its use. 

InFocus does not warrant that the operation of the products will be uninterrupted or error-free. InFocus is not 
responsible for damage arising from failure to follow instructions relating to the products’ use. 

INFOCUS IS NOT RESPONSIBLE FOR DAMAGE TO OR LOSS OF ANY PROGRAMS, DATA, OR REMOVABLE 
STORAGE MEDIA. INFOCUS IS NOT RESPONSIBLE FOR THE RESTORATION OR REINSTALLATION OF 
ANY PROGRAMS OR DATA OTHER THAN SOFTWARE INSTALLED BY INFOCUS WHEN THE PRODUCT IS 
MANUFACTURED.

To enable InFocus to provide the best possible support and service during the Limited Warranty Period, you will be 
required to:

Summary of Contents for INF8022











































Reviews: