background image

 

User Precautions: Safety, Warranty and Use 

The following will assist you in fulfilling any warranty obligations

.

 

 

Do Not Modify this radio for any reason. Do not disassemble the radio.  

Failure to comply may void Warranty and governmental approvals. No 

User Serviceable Parts inside. Refer repair to Factory Authorized Per-

sonnel only. 

 

Do Not Use the transceiver or charge the battery in an explosive envi-

ronment. 

 

Keep the transceiver out of direct sunlight, DO NOT expose the unit to 

extreme heat or cold. 

 

Keep the transceiver out of dusty or humid areas. IF IMMERSED IN 

WATER, TAKE OUT OF WATER AND BLOW AIR ACROSS THE 

SPEAKER AND SHAKE ANY WATER THAT MAY BE TRAPPED IN 

FRONT OF THE SPEAKER GRILL. 

 

Do Not Transmit without an approved antenna connected to the trans-

ceiver. 

Install the battery only after the antenna is connected to the 

radio. Fully charge the battery first to condition it.

 

 

Observe common sense when attempting to transmit in areas such as 

construction sites, mines, hospitals, hazardous environments, etc.. 

Turn off your radio before entering any area with a potentially 

       explosive atmosphere (where the air contains gas, dust), as well as  

       while taking on fuel, etc.). 

 

Typically transmit for no longer than 1 minute with a rest period of 4 

minutes. Longer transmission times will see the rear side of the radio 

heat up. 

 

If the radio emits smoke or strange odors, turn the radio off, discon-

nect the battery and promptly contact your local authorized Infinity 

Dealer or Re-Seller. 

About  your  radio: 

Infinity radios are sold only through Infinity or Au-

thorized Resellers. The radio is also field programmable using the key-

pad,  software,  or  wired  cloning  (if  enabled  by  the  software);  and  may 

come  pre-programmed  with  either  factory  defaulted  programming  or 

other  User  channels.  Full  function  access  to  the  radio  and  options  is 

only available if the optional Infinity programming software with the ap-

propriate  interface  cable  has  been  purchased.  The  sale  and  use  of 

these radios is restricted to licensed users only. User takes the respon-

sibility  to  comply  with  FCC  and  other  governmental  or  local  require-

ments. 

CONDITION  OF  SALE:  The  User  is  familiar  with  radio  opera-

tions,  radio  configuration  and  radio  terminology. 

It  is  important 

that the User is aware of and understands hazards common to the op-

eration of any radio transceiver. 

Thank-you for selecting the K-911 for 

your radio communications needs! 

 

  

25 

13.0  PROGRAMMING  VIA  SOFTWARE 

Your radio comes pre-

programmed  with  some  channels  for  test.  The  Programming  kit  comes  with  a 

USB  cable,  Programming  Software    and  a  USB  cable  driver  for  WIN  XP  and 

Win7,(Model PG-12). (For Win 8, Order  Model PG-13.) 

PC  SKILLS  AS  WELL 

AS  FAMILIARITY  WITH  TWO  RADIOS  ARE  NECESSARY

. You will need to 

unzip  the  files  provided  using  a  free  program  called  WINRAR  from  WIN  RAR 

LABS and is available as a free download from the Internet. 

When downloading, 

just download only the free unzip  program. In preparation for programming:

 

 

(1)  Load (unzip) the USB driver onto the PC. Install the USB driver. 

 

(2)  Load (unzip) the Programming Software onto your PC. 

 

(3)  Restart the PC. 

 

(4)  Connect the supplied USB driver to an available port on the PC 

 

(5)  Check  with  Windows  device  manager  that  the  USB  cable  is  operating  and 

seen by the PC 

 

(6)  START  the programming software by clicking on the  K-911 Icon that is on 

your desktop, placed automatically by extracting the software from the exe-

cutable file. THE FOLLOWING SCREEN APPEARS: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(7)  CLICK  ON  SETTING;  PORT.  A  POP  UP  SCREEN  WILL  APPEAR  WITH 

THE PORT NUMBER CORRESPONDING TO THE USB CABLE.  (example, 

COM  5).  THEN  PRESS  OK.  IF  NO  PORT  NUMBER  APPEARS,  CHECK 

WINDOWS DEVICE MANAGER TO MAKE SURE THAT THE USB CABLE 

DRIVER (PROLIFIC) HAS  BEEN SUCCESSFULLY INSTALLED.  

 

(8)  WITH  RADIO  ON  AND  CABLE  CONNECTED,  THEN  perform  a   

READ 

FROM  RADIO,  then  save  the  file,  NAMING  IT  AS  AN  EXAMPLE, 

ORIGINAL 

FILE

”. 

 

 

(9)  THEN  make  changes  as  needed,  then  SAVE  THE  FILE,  EXAMPLE,  AS 

MASTER 1 FEB 

2015”,  

THEN WRITE TO RADIO. 

COM 5 

Summary of Contents for K911AD1















Reviews: